Bosch CMG976K 1 Series Manuale d'uso e istruzioni per l'installazione - Pagina 18
Sfoglia online o scarica il pdf Manuale d'uso e istruzioni per l'installazione per Forno Bosch CMG976K 1 Series. Bosch CMG976K 1 Series 48.
Stampa la pagina
en Ventilation function "Crisp Finish"
Press
" Cooking time".
5.
A cooking time must always be set to operate the
microwave.
To change the preset cooking time, press the relev-
6.
ant time value, e.g. minute display "m" or second
display "s".
a The selected value is marked in blue.
Use the setting ring to set the cooking time.
7.
If required, use
to reset the setting value.
To confirm the set cooking time, press
8.
play.
Press
to start the operation.
9.
a The microwave starts and the cooking time counts
down. The display shows the performance reduction
for the maximum microwave output "Boost".
→ "Microwave output settings", Page 11
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
10.
Once the cooking time has elapsed:
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
If you have switched off the drying function for the
11.
microwave in the basic settings and condensation
has formed in the cooking compartment, dry the
cooking compartment.
→ "Drying", Page 27
Note: If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→ "Basic settings", Page 21
Changing the microwave output
You can change the microwave output at any time.
Press
on the display.
1.
Press the microwave output
2.
Use the setting ring to set the microwave output.
3.
To confirm the change, press
4.
a The change is applied.
Changing the cooking time
You can change the cooking time at any time.
Press
on the display.
1.
12 Ventilation function "Crisp Finish"
The ventilation function "Crisp Finish"
ture from the cooking compartment so that your food
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
12.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
You can use the ventilation function for the following
types of heating:
¡ 4D hot air
18
on the dis-
to switch the ap-
.
on the display.
extracts mois-
Press the cooking time
2.
Use the setting ring to change the cooking time.
3.
To confirm the change, press
4.
a The change is applied.
11.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡ → "Safety", Page 2
¡ → "Preventing material damage", Page 6
¡ → "Microwave output settings", Page 11
¡ → "Cookware and accessories with microwave",
Page 16
Requirement: Observe the information about the re-
spective operating mode.
→ "Setting options with the microwave", Page 17
Press the operating mode that you require in the
1.
menu.
Select the settings for the operating mode, e.g. type
2.
of heating and temperature.
Press
"Added microwave".
3.
Use the setting ring to set the microwave output.
4.
To confirm the set microwave output, press
5.
the display.
Press
"Cooking time" and set the cooking time.
6.
Press
to start the operation.
7.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
8.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
Press
on the display.
1.
Press the microwave output
2.
Change or deactivate added microwave with the
3.
setting ring.
To confirm the change, press
4.
a The change is applied.
¡ Top/bottom heating
¡ Circulated air grilling
¡ Pizza setting
12.2 Setting the ventilation function
You can activate the ventilation function at any time,
even after the start of the operation.
1.
Set a suitable type of heating and a temperature.
If required, you can select other settings and com-
bine with the ventilation function.
Press
"Crisp Finish".
2.
a The
symbol lights up red.
Press
to start the operation.
3.
.
on the display.
on
to switch the ap-
.
on the display.