AirStage UTY-LNHG Manuale operativo - Pagina 5

Sfoglia online o scarica il pdf Manuale operativo per Telecomando AirStage UTY-LNHG. AirStage UTY-LNHG 10. Wireless
Anche per AirStage UTY-LNHG: Manuale di installazione (10 pagine)

Stampa la pagina
About Mode Operation
Heating:
● Use to warm your room.
● When Heating mode is selected, the air conditioner will
operate at very low fan speed for about 3 to 5 minutes, after
which it will switch to the selected fan setting. This period of
time is provided to allow the indoor unit to warm up before
beginning full operation.
● When the room temperature is very low, frost may form on
the outside unit, and its performance may be reduced. In or-
der to remove such frost, the unit will automatically enter the
defrost cycle from time to time. During Automatic Defrosting
operation, the OPERATION Indicator Lamp (green) will fl ash,
and the heat operation will be interrupted.
● After the start of heating operation, it takes some time before
the room gets warmer.
Cooling:
● Use to cool your room.
Dry:
● Use for gently cooling while dehumidifying your room.
● You cannot heat the room during Dry mode.
● During Dry mode, the unit will operate at low speed; in order
to adjust room humidity, the indoor unit's fan may stop from
time to time. Also, the fan may operate at very low speed
when adjusting room humidity.
● The fan speed cannot be changed manually when Dry mode
has been selected.
Fan:
● Use to circulate the air throughout your room.
During Heating mode:
Set the temperature to a temperature setting that is higher than the
current room temperature. The Heating mode will not operate if the
preset temperature is set lower than the actual room temperature.
During Cooling/Dry mode:
Set the temperature to a temperature setting that is lower than the cur-
rent room temperature. The Cooling and Dry modes will not operate if
the preset temperature is set higher than the actual room temperature
(in Cooling mode, the fan alone will operate).
During Fan mode:
You can not use the unit to heat and cool your room.

TIMER OPERATION

Before using the timer function, be sure that the Remote Control
Unit is set to the correct current time (See page 2).
To Use the ON timer or OFF timer
1
Press the "START/STOP" button
(If the unit is already operating, proceed
to step 2).
The receiver unit control panel's OPERATION Indicator
Lamp (green) will light.
2
Press the "TIMER MODE" button to se-
lect the OFF timer or ON timer operation.
Each time the button is pressed the timer function changes
in the following order:
CANCEL
PROGRAM
(OFF → ON, OFF ← ON)
The receiver unit control panel's TIMER Indicator Lamp
(orange) will light.
AMP Air Conditioning
OFF
ON
3
Use the "TIMER
adjust the desired OFF time or ON time.
Set the time while the time display is fl ashing (the fl ashing
will continue for about 5 seconds).
button: Press to advance the time.
button: Press to reverse the time.
About 5 seconds later, the entire display will reappear.
To Cancel the Timer
Use the "TIMER MODE" button to select "CANCEL".
The air conditioner will return to normal operation.
To Change the Timer Settings
Perform steps 2 and 3.
To Stop Air Conditioner Operation while the Timer is Op-
erating
Press the "START/STOP" button.
To Change Operating Conditions
If you wish to change operating conditions (Mode, Fan Speed, Tempera-
ture Setting), after making the timer setting wait until the entire display
reappears, then press the appropriate buttons to change the operating
condition desired.
To Use the Program timer
1
Press the "START/STOP" button
(If the unit is already operating, proceed
to step 2).
The receiver unit control panel's OPERATION Indicator
Lamp (green) will light.
2
Set the desired times for OFF timer and
ON timer.
See the section "To Use the ON timer or OFF timer" to set
the desired mode and times.
About 5 seconds later, the entire display will reappear.
The receiver unit control panel's TIMER Indicator Lamp
(orange) will light.
3
Press the "TIMER MODE" button to se-
lect the PROGRAM timer operation (OFF
ON or OFF
The display will alternately show "OFF timer" and "ON
timer", then change to show the time setting for the opera-
tion to occur fi rst.
● The program timer will begin operation. (If the ON timer
has been selected to operate fi rst, the unit will stop
operating at this point.)
About 5 seconds later, the entire display will reappear.
To Cancel the Timer
Use the "TIMER MODE" button to select "CANCEL".
The air conditioner will return to normal operation.
To Change the Timer Settings
1. Follow the instructions given in the section "To Use the ON Timer or
OFF Timer" to select the timer setting you wish to change.
2. Press the "TIMER MODE" button to select either OFF
or OFF
ON.
To Stop Air Conditioner Operation while the Timer is Op-
erating
Press the "START/STOP" button.
www.ampair.co.uk | [email protected]
/ TIMER
" button to
ON will display).
En-4
ON