Anchor Explorer PA-2500 Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Altoparlanti Anchor Explorer PA-2500. Anchor Explorer PA-2500 7.

Stampa la pagina

Battery Operation

Caring for the built-in battery

It is very important that you fully charge the battery in your

system before first use, and as soon as possible after each and

every use—even if operated only briefly.

IMPORTANT: Do not store system with a partially or fully

discharged battery, as this will reduce battery service life.

When the "Battery" LED begins flashing:

BATTERY

Flashing = low battery.

When the Battery LED begins flashing, this indicates the battery

is low and the unit will automatically shut off in 15 -30 minutes.

Charging the battery

Plug the power cord into an AC outlet (the Charger LED will

CHARGER

light, indicating the battery is being charged).

Plug cord into AC outlet.

Light On = charging.

Flashing = fully charged.

When the battery is charged (about 10 hours), the Charger

LED will flash. This indicates the charger has switched to the

maintenance charge rate—the charger may be left plugged in

to maintain a full charge without damaging the battery.

To squeeze a

IMPORTANT: For longer battery life, always store the unit

little more time

with the battery in a fully charged condition.

out of a fully-

charged unit,

Expected service time per charge

plug the AC

power cord into

Battery service time will vary depending on the volume level

an outlet while

and type of program usage. You can expect about 6-8 hours of

you're using

operation at medium volume, 3-4 hours at full volume of

the system.

continuous music input (longer for speech applications).

Accessories

MIC-90 Handheld Microphone

Anchor's dynamic, balanced, low impedance microphone

with a unidirectional pick-up pattern. It has a on/off switch

and comes with a 20' cable and mic clip.

MIC-50 Handheld Microphone

An unbalanced, low impedance microphone with a privacy

on/off switch. It has a 1/4" phone plug attached to a 10' cable.

P-2501 Companion Speaker

An unpowered speaker which connects to the speaker output

of an AC powered Explorer for increased crowd coverage.

- Model PB-2500

(for Mic 1 Input)

(for Mic 2 Input)

(for AC Explorer only)

Thank you for choosing an Anchor Audio portable sound system. Our products

incorporate state-of-the-art design and the finest quality of materials and

workmanship. We're proud of our products and appreciate the confidence which

you have shown by selecting an Anchor system.

I hope you'll take a few of minutes to review this manual. We've incorporated

several unique features into our products, and your knowledge of how to use

them will enhance the performance and your enjoyment of the system.

David Jacobs, President on behalf of all Anchor employees

Quick Use Guide

The Explorer is a high-fidelity portable sound system that's

simple to set up and use. You'll need a microphone or some

other input source before before you get started.

If you have a battery powered model, make sure the battery

is fully charged before use (see page 10).

Here's how easy it is to use

1. Set the unit in front of your audience on the floor,

table or on a speaker stand.

Problems?

2. Plug a microphone into the Mic 1 or Mic 2 input,

Consult the

or plug an audio source into the line input.

troubleshooting

section on the

3. Set all input level controls to minimum, and set the

back page of

bass and treble controls to the 12:00 position.

this manual.

4. Turn the power switch ON (plug in the power cord if

you're using an AC model). Slowly increase the level

control adjacent to the input used until desired volume

is reached.

5. Adjust the bass and treble for desired sound quality.

To operate the wireless mic system on wireless models, see

"Wireless Operation" on pages 8 and 9. And for more detailed

instructions, see the "Operation" section beginning on page 6.