Bosch 23 Manuale per l'installazione e l'uso - Pagina 15

Sfoglia online o scarica il pdf Manuale per l'installazione e l'uso per Utensile elettrico Bosch 23. Bosch 23 18. Angle exact
Anche per Bosch 23: Manuale di istruzioni originale (22 pagine)

Stampa la pagina

Bosch 23 Manuale per l'installazione e l'uso

1. Putting into Operation

BTEXACT_bu_3609929A44_t.fm Seite 14 Montag, 5. September 2005 2:12 14

LED Indicators

Battery Condition Indicator

If the charging of the battery 18 is neces-

sary, the LED indicator 11 blinks green.

You can still use the power tool for approx.

6–8 screw fasteners.

If the LED indicator lights red, the capacity is no long-

er adequate for another screwing fastener. The pow-

er tool can no longer be switched on. The switch-on

lock remains active until a charged battery is inserted.

A considerably shortened operating time of the pow-

er tool after each charging indicates that the battery

must be replaced soon. Dispose of the used battery

in accordance with the legal/country-specific regula-

tions.

Note: If, instead of the rechargeable battery 18, a

voltage adapter and the constant voltage regulator

4EXACT are used, the LED indicator 11 has no func-

tion.

Screwing Fastener Indicator

When the preset torque is reached, the

switch-off coupling responds. The LED in-

dicator 9 lights green.

If the preset torque is not reached, the LED indicator

9 lights red and an acoustical signal sounds. The

screwing fastener must be performed again.

Bluetooth

Connection Indicator

Press the on/off switch 12 in order to activate the

Bluetooth

connection. The red LED indicator 10

blinks as long as the screw driver searches for a con-

nection.

A red light of the LED indicator 10 that lights contin-

uously shows that the Bluetooth

been made. The screwdriver is still locked, however.

If the driver is released by access point EXAConnecT,

the LED indicator 10 goes out.

If the LED indicator 10 blinks only briefly after the

on/off switch is pressed and then goes out, the pow-

er supply of the driver is no longer adequate for a

screwing fastener.

3 609 929 A44 • (05.09) T

Repeat Protection

When the switch-off coupling responds for a screw-

ing fastener, the motor switches off. Switching on

again is possible only after a 0.7 second delay. In this

manner, an unintentional re-tightening of an already

seated screw is avoided.

Adjusting the Angled Drive Head

Type 0 602 491 647/... 650/... 651/... 652/... 656/

The angled drive head 3 can be adjusted to a total of

eight positions.

Hold the machine with the open-ended spanner 6 on

the spanner flats 5 of the angled head flange.

Never clamp the machine on the housing shells.

Loosen with the open-ended spanner 4 on the span-

ner flats 16 of the nut sleeve. Adjust the angled drive

head 3 in 45° steps to the desired position and

retighten with the open-ended spanner 4 on the

spanner flats 16 of the sleeve nut. Hold the angled

head flange with the open-ended spanner 6 to pre-

vent turning.

Adjusting the LED Working Position

Type 0 602 491 647/... 650/... 651/... 652/... 656/

connection has

Press off the marking ring 19 with a thin screwdriver

blade, a knife, or similar. Slide the spring ring 30 with

spring ring pliers to the rear onto the housing shell.

The two shell halves of the LED holder 15 that en-

English–14

... 669/... 671/... 673/... 675