Anchor Explorer Pro Manuale d'uso - Pagina 2
Sfoglia online o scarica il pdf Manuale d'uso per Sistema di altoparlanti Anchor Explorer Pro. Anchor Explorer Pro 8. Anchor audio portable sound system
Anche per Anchor Explorer Pro: Manuale d'uso (8 pagine), Manuale d'uso (4 pagine), Manuale d'uso (13 pagine)
Stampa la pagina
Explorer Pro Sound System Owners Manual
BASIC SYSTEM OPERATION
NOTE: Fully Charge Batteries Before First Use!
1. Set all Input Level Controls to minimum
& Tones Controls to flat or the middle
setting before turning your system on
2. Plug a wired microphone into the MIC
1 or MIC 2 jacks and/or plug an audio
source into the LINE-IN jack
3. Switch POWER to ON, the BATTERY LED
will light
4. Slowly increase the Level Control for the
input jacks used to the desired volume
5. Adjust BASS & TREBLE controls to
desired sound quality
IMPORTANT: Make all connections with shielded
cables to avoid hum, buzzing or interference.
SPEAKER STAND SETUP
1. Loosen the Lower Collar Knob
2. Separate the stand legs until the leg support Cross
Braces are parallel to the floor
3. Tighten the Lower Collar Knob
4. Loosen the Upper Collar Knob and extend the
center pole
5. Adjust height and retighten the Upper Collar Knob
6. Place your Anchor sound system on the stand
UPPER
COLLAR
KNOB
LOWER
COLLAR
KNOB
CROSS BRACES
RX INDICATOR LIGHTS FOR
WIRELESS RECEIVER 1
A solid red light on one of the
RX Indicator Lights indicates
that the sound system is getting
good reception with the wireless
A solid red light on both RX
Indicator Lights indicates that
the sound system is a optimum
reception with the wireless
RX INDICATOR LIGHTS FOR
WIRELESS RECEIVER 2
WIRELESS MICROPHONE 1
wireless microphone levels
WIRELESS MICROPHONE 2
SPEAKER STAND ADAPTER
The 1.5" diameter Speaker Stand
Adapter lets you mount the
Explorer on a speaker stand.
AC POWER CORD INLET
1. Slide Speaker Stand Adapter
into slot on Explorer PRO
bottom
2. Tighten screw to secure
adapter
3. Place unit on stand carefully
4. Tighten screw on Adapter
collar securing Explorer PRO
on stand
For System Setup & Operation Videos Visit Our Website: www.anchoraudio.com
BACK PANEL OF EXP-7500U2
LINE OUT - OUTPUT JACK
Balanced 1/4" – provides a combined
output of all active system inputs
Record your presentation or connect to
WIRELESS RECEIVERS 4
another powered sound system
(see page 6)
microphone
WIRELESS 1
WIRELESS 2
9
9
microphone
VOLUME
VOLUME
LEVEL CONTROL
Adjust knob to control
LEVEL CONTROL
POWER INLET
100-240 VAC, 47-63 Hz
(250 WATTS MAX)
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
POWER SWITCH
CHARGE INDICATOR LIGHT (AC/DC only)
LINE IN
LINE IN
L
R
VOLUME
LINE OUT
TREBLE
BASS
MIC 1
MIC 1
VOLUME
MIC 2
MIC 2
VOLUME
MUSIC
CHARGE STATUS
SPEECH
VOICE
OVER
BATTERY EMPTY
OFF
POWER
SPEAKER OUT
ON
BATTERY LEVEL
INDICATOR LIGHT
(AC/DC only)
MADE IN USA
SIX YEAR WARRANTY
LINE IN - INPUT JACKS
The 1/8" (3.5 mm) jack input is used to hook
up an iPod, a portable CD/ MP3/ tape player,
laptop computer, or similar external
audio source
The 1/4" unbalanced input can be used for
other communication devices including a
mixer or daisy chaining together multiple
Explorer speakers
LINE IN LEVEL CONTROL
TONE CONTROLS - BASS/TREBLE
WIRED MIC LEVEL CONTROLS
MUSIC/ SPEECH BUTTON
In situations where you're speaking to
a larger crowd or in a noisy environ-
ment, just push the Music/Speech
button in and give your voice an added
boost
To return back to normal use, just push
the Music/Speech button again
VOICE OVER BUTTON
Push the "Voice Over" button in
to have the music automatically
lowered when you speak through a
connected microphone
Music will return to original level
when mic use/speaking stops
SPEAKER OUT -
OUTPUT JACK
Connect the system to a
Explorer PRO unpowered
companion speaker
2