Electrolux EIDW6305 Scheda tecnica del servizio

Sfoglia online o scarica il pdf Scheda tecnica del servizio per Lavastoviglie Electrolux EIDW6305. Electrolux EIDW6305 2. Wiring diagram (all languages)
Anche per Electrolux EIDW6305: Istruzioni per l'installazione (2 pagine)

Stampa la pagina

Exploded View of Wash System

Pump Assembly

The pump assembly is driven by a permanent

The drain valve is connected to the drain pump

split capacitor motor. When looking at the output

by a rubber hose and is mounted to the

shaft, rotation is in the counterclockwise direction

dishwasher base. The drain valve maintains

at 3300RPM when driven by 120V 60Hz AC

pressure in the pressurized fine filter. The

signal. The motor drives a pump which supplies

intermediate drain hose is attached by a worm

100% filtered water at the rate of approximately

gear clamp to the discharge end of the drain

19 GPM to all three spray arms at once.

valve.

Draining is accomplished by using a small

The drain hose must have a loop at a minimum

seperate synchronous drain pump mounted to

height of 32 inches in order to ensure proper

the sump. The drain pump is connected to the

drainage.

sump by a small rubber hose and two mounting

The main pump is removed by disconnecting

points. A check valve is located at the discharge

both attached clamps and hoses, removing the

end of the drain pump.

three screws that secure the motor base to the

dishwasher base, unlatching the leak detector,

and disconnecting the wiring harness

connections to the pump assembly.

Componenet Error LED Indications

To gain access to the Control Housing Assem-

bly, remove kickplate assembly. LED indicates

which component is the source of the error.

Standard Dry Air Flow

air is mixed with hot, humid air existing the tub

When the control advances to the "dry" portion of

the cycle, the lower fan located in the Lower

in the Lower Drying Duct Assembly. This lowers

Drying Duct Assembly is activated. Then, the

the temperature and humidity of the air exiting

the unit through the toe and kickplate. The

Vent Assembly located in the top right corner of

the tub is activated. The vent fan draws in the air

addition of cooler, dryer outside air helps to

from outside the tub forcing the hot, humid air out

speed evaporation of water from the hot dishes.

the Side Drying Duct Assembly and into the

Lower Drying Duct Assembly. Cool dry outside

Detergent and Rinse Aid Dispenser

The detergent and rinse aid dispenser is a one

To replace dispenser:

piece component consisting of a molded

• shut off electricity to dishwasher,

detergent cup and a built-in rinse aid dispenser.

• remove outer door panel assembly and foam

barrier,

The detergent cup has a spring loaded cover

• disconnect wiring to the dispenser,

and the rinse aid dispenser has a removable

• remove the six screws and bracket,

cover.

• remove the dispenser,

Liquid rinse aid is added to the dispenser up to

• replace and reinstall in reverse order,

the fill line indicator. The amount of rinse aid

• rewire actuator.

released can be adjusted by turning the arrow

indicator from one, being the least amount, to

four, being the greatest amount.

Tub Gasket

3. Press the gasket while stretching around

The door gasket is pressed into the tub channel

the corners.

for an interference fit. To install the gasket:

1. Locate the center mark on the gasket and

NOTE: There should be no wrinkles or

puckers in the corners.

press into place.

4. Place the gasket end at the bottom and

2. Press the gasket across the header using

your thumb.

then press the gasket in from the bottom up.

Product Specifications

Electrical

Water Supply

Suggested minimum incoming water

Rating ................................... 120 Volts, 60Hz

temperature ............................. 120°F (49°C)

Separate Circuit..15 amp min.- 20 amp max.

Motor (Amps) ........................................... .75

Pressure (PSI) min./max. ................... 20/120

Heater Wattage ..................................... 1200

Connection (NPT) .....................................

Total Amps (load rated) ........................ 10.0

Consumption (Normal Cycle) .......................

TempAssure .............................. 140°F ±5°F

............. 4.9 - 9.7 U.S. gal., 18.5 - 36.7 liters

(60°C±3°C) [with outer door in place]

Water valve flow rate (U.S. GPM) ........... .83

TempBoost ............. 145°F ±5°F (63°C ±3°C)

Water recirculation rate (U.S. GPM) ..............

Heated Wash/Heated Rinse

.................................................... approx. 19

Sanitize .................. 150°F ±5°F (66°C ±3°C)

Water fill time ................................... 87 sec.

Hi-Limit Thermostat ................ 200°F (93°C)

Trouble Shooting Tips

Personal Injury Hazard

Always disconnect the dishwasher from the electrical power source before adjusting or

replacing components.

Symptom

Check the Following

Dishwasher will not operate when

1. Fuse (blown or tripped).

turned on.

2. 120 VAC supply wiring connection

faulty.

3. Electronic control board defective.

4. No 12 VAC power to control.

5. Motor (inoperative).

6. Door switch (open contacts).

7. Door latch not making contact with

door switch.

8. Touch pad circuit defective.

9. No indicator lamps illuminate when

START or OPTIONS are pressed.

Motor hums but will not start or

1. Motor (bad bearings).

run.

2. Motor stuck due to prolonged

non-use.

1. Improper voltage.

Motor trips out on internal thermal

2. Motor windings shorted.

overload protector.

3. Glass or foreign items in pump.

1. Heater element (open).

Dishwasher runs but will not heat.

2. Electronic control board defective.

3. Wiring or terminal defective.

4. Hi-Limit thermostat defective.

1. Latch mechanism defective.

Detergent cover will not latch or

2. Electronic control board defective.

open.

3. Wiring or terminal defective.

4. Broken spring(s).

5. Defective actuator.

Dishwasher will not pump out.

1. Drain restricted.

2. Electronic control board defective.

3. Defective drain pump.

4. Blocked impeller.

5. Open windings.

6. Wiring or terminal defective.

7. Defective Drain Valve.

Dishwasher will not fill with water.

1. Water supply turned off.

2. Defective water inlet fill valve.

3. Check fill valve screen for

obstructions.

4. Defective float switch.

5. Electronic control board defective.

6. Wiring or terminal defective.

7. Float stuck in "UP" position.

Dishwasher water siphons out.

1. Drain hose (high) loop too low.

2. Drain line connected to a floor drain

not vented.

3. Drain valve or pump stuck open.

1. Detergent allowed to stand too long

Detergent left in dispenser.

in dispenser.

2. Dispenser wet when detergent was

added.

3. Detergent cover held closed or

blocked by large dishes.

4. Improper incoming water

temperature to properly dissolve

detergent.

5. See "Detergent cover will not open."

6. Spray arm blocked.

7. Is water getting into the unit.

Remedy

1. Replace fuse or reset breaker.

2. Repair or replace wire fasteners at

dishwasher junction box.

3. Replace control board.

4. Replace control board.

5. Replace motor/impeller assembly.

6. Replace latch assembly.

7. Replace latch assembly.

8. Replace console assembly.

9. Replace console assembly.

1. Replace motor assembly.

2. Rotate motor impeller.

1. Check voltage.

2. Replace motor/impeller assembly.

3. Clean and clear blockage.

1. Replace heater element.

2. Replace control board.

3. Repair or replace.

4. Replace thermostat.

1. Replace dispenser.

2. Replace control board.

3. Repair or replace.

4. Replace dispenser.

5. Replace dispenser.

1. Clear restrictions.

2. Replace control board.

3. Replace pump.

4. Check for blockage, clear.

5. Replace pump assembly.

6. Repair or replace.

7. Repair or replace.

1. Turn water supply on.

2. Replace water inlet fill valve.

3. Disassemble and clean screen.

4. Repair or replace.

5. Replace control board.

6. Repair or replace.

7. Clean or replace float.

1. Repair to proper 32-inch minimum

height .

2. Install air gap at counter top.

3. Repair or replace.

1. Instruct customer/user.

2. Instruct customer/user.

3. Instruct customer/user on proper

loading of dishes.

4. Incoming water temperature of

120°F is required to properly

dissolve dishwashing detergents.

6. Instruct customer/user.

7. Check fill valve repair or replace

010108