Atlantic TidalWave FP500 Series Manuale operativo - Pagina 2

Sfoglia online o scarica il pdf Manuale operativo per Pompa dell'acqua Atlantic TidalWave FP500 Series. Atlantic TidalWave FP500 Series 4.

Stampa la pagina

Introduction

Thank you for selecting the TidalWave FP100, FP200, FP300, FP400 or FP500 series

pump. Before using this pump please take a moment to review this manual.

To avoid an accident do not use the pump in any way other than as described in this

manual. Please note the manufacturer cannot be responsible for accidents arising because

the product was not used as prescribed. After reading this manual keep it as a reference

in case questions arise during use.

Flow Chart:

Max

Model #

Watts

FP100

120

FP200

9.5

175

FP300

325

FP400

370

FP500

525

Prior to Operation and Installation

• When the pump is delivered, first perform the following checks:

•

Check for any damage to pump and power cable that may have occurred during

the shipment.

•

Check the model number to make sure it is the product that was ordered and verify

the voltage and frequency are correct.

Caution

• DO NOT operate this product under any condition other than those for which it is

specified. Failure to observe this precaution can lead to electrical shock, electrical

leakage, fire, water leakage or other problems.

• The pump is a 110/120 volt 60 Hz pump, please only use with a power supply voltage

within 110-120 volt 60 Hz.

• Never place your hand or any object in or near the inlet opening while this equipment is

operating. If pump inlet is clogged, always turn off the power supply and wait until the

motor is completely stopped before attempting to remove any clogged material.

• Please make sure that the power plug and the AC outlet receptacle are protected and away

from water or pump discharge hose to prevent accidental electric shock or short circuit.

• Always operate the pump completely submerged in water.

• Avoid dry operation, which will not only lower performance but can cause the pump to

overheat/malfunction, leading to electrical leakage, shock or premature failure.

• Always turn off power or unplug the pump prior to performing any maintenance or

placing your hands into the water.

• CAUTION:

THIS PUMP IS TO BE USED IN A CIRCUIT PROTECTED BY A GROUND CIRCUIT INTERRUPTER.

2.5'

7.5'

100

230

290

180

430

300

• CAUTION:

THIS PUMP HAS BEEN EVALUATED FOR USE IN WATER ONLY.

• WARNING:

RISK OF ELECTRIC SHOCK - THIS PUMP IS SUPPLIED WITH A GROUNDING CONDUCTOR

AND GROUNDING-TYPE ATTACHMENT PLUG. TO REDUCE THE RISK OF ELECTRIC SHOCK,

BE CERTAIN THAT IT IS CONNECTED ONLY TO A PROPERLY GROUNDED, GROUNDING

TYPE RECEPTACLE.

Electrical Safety

• Electrical wiring should be installed by a qualified electrician in accordance with all

applicable safety regulations. Incorrect wiring can lead to a pump malfunction, electrical

shock or fire.

• Pumps should operate on a designated, 110/120 volt circuit.

• Pump must be protected by a ground fault circuit interrupter (GFCI).

• Pump must be plugged into a standard, properly grounded, three pronged outlet.

Safety Instructions

Make sure the pump works at a proper water level. Do

not operate the pump without water. If so, the pump

should be turned off immediately and check.

ATTENTION

Fig. 1

Fig. 2

• Do not lift, lower or handle the pump by pulling on the electrical cord. Make sure the

electrical cable does not become excessively bent or twisted and does not rub against a

structure in a way that might damage it. (Fig. 1)

• Always disconnect the power supply before doing any maintenance or placing your hands

into the water to which this pump is immersed. (Fig. 2)

• The submersible pump should not be used if the electrical supply cable is damaged in

any way. If a cable with damaged insulation is submerged in water, there is danger of

water seeping into the pump motor and causing a short. The electrical cable cannot be

replaced. If the cord is damaged, the pump should be discarded. Altering the electrical

cable in any way will void the warranty. (Fig. 3)

Operation

• Fountain Series pumps are for use in water only. Water temperature should never

exceed 95˚ F (35˚ C).

Fig. 3