Atlantic Technology 6200C Manuale di istruzioni - Pagina 9
Sfoglia online o scarica il pdf Manuale di istruzioni per Altoparlanti Atlantic Technology 6200C. Atlantic Technology 6200C 12. High performance c.o.r.e. technology loudspeaker components
Instruction Manual
The terminals themselves are designed to allow the use of very heavy
speaker wire or connectors. Be sure to tighten them securely, but don't
over-tighten them.
WARNING: To prevent risk of electrical shock or damage to your
equipment, always switch off the amplifier or receiver when making
any system connections.
You can connect your speakers by using a variety of audio connectors such
as banana plugs (single or double), pin connectors, spade lugs, etc., or you
can:
1. Remove .5" of insulation from each wire end.
2. Twist the stranded wire together, keeping the two ends
separate.
3. Place the appropriate wire through the appropriate
postholes in the connectors. These holes are revealed when
you loosen the connector's capscrew.
4. Screw down the capscrew tightly, but be careful not to over
tighten it.
5. Check the tightness of the capscrews 24 hours after hookup
and occasionally after that, as they can loosen over time.
We recommend that you check your local electrical codes to make sure that
you are not using improper connectors.
It's important to observe polarity while making speaker connections: red
(+) terminals on the amplifier to red (+) on the speaker, black (–) on the
amplifier to black (–) on the speaker. Look carefully at the wires you are
using and note that one of the conductors of each pair will typically be
identified by color, printing on the outer jacket, ridges on the outer jacket,
or a thread intertwined with the wire strands. By convention, the marked
wire is connected to the red (+) terminal.
Whether your are connecting a complete system,or adding a single speaker
component to your present system, the wiring should look like one of the
system wiring diagrams on pages 7 and 8.
WARNING: Before turning on the amplifier, be certain that no stray
wire strands are touching across any terminals as this might damage
your amplifier.
Finally, check the polarity of your front speakers by listening to some ste-
reo music with good bass content. If the sound seems"hollow", unusually
spread out, or seem to have weak mid-bass, recheck your connections for
proper polarity and correct any out of phase connections,if necessary.
System Setup
Bass Management
Some older surround sound decoders and receivers offer a choice of "Nor-
mal"or"Wide-band"modes for the center channel speaker.The Model 8200
C is designed to be used in the Normal mode.Additionally,digital processing
multi-channel systems provide a Bass Management menu,which typically
requires you to select between "Small" or "Large" speakers during system
set-up. Since these systems have been designed to work with a dedicated
subwoofer,please set all the speakers in Systems 6200 and 8200 to Small.
Operation of the Rear Panel Controls
on the LCR Speakers
HF ENERGY
– REVERBERANT
+ DAMPED ROOM
0 THX / AVERAGE
faces. The Reverberant position is designed for rooms with an abundance
LOCATION
of reflective surfaces like hardwood or tile floors,glass walls,etc.It decreases
BEHIND SCREEN
HF ENERGY
the high frequency output of the speaker to reduce excess HF energy that
builds up in live rooms. The Damped position brings the tweeter's output
– REVERBERANT
THX / NORMAL
slightly above flat response to compensate for overly absorbent rooms with
+ DAMPED ROOM
lots of soft surfaces.Speakers in overly damped rooms can sound dead and
0 THX / AVERAGE
BOUNDARY
lifeless unless compensated.
COMPENSATION
ON
LOCATION
THX / NORMAL
BEHIND SCREEN
HF ENERGY
– REVERBERANT
THX / NORMAL
+ DAMPED ROOM
0 THX / AVERAGE
BOUNDARY
are located behind a perforated video screen or curtains. Of course, if you
COMPENSATION
choose to place the speakers behind curtains it is important to choose a
LOCATION
ON
material that is as acoustically transparent as possible. Looking through
BEHIND SCREEN
the material into the light can give you some indication of the material's
THX / NORMAL
transparency in this regard.The more light and detail you can see,the bet-
ter it will be acoustically.
THX / NORMAL
BOUNDARY
COMPENSATION
ON
THX / NORMAL
To set these controls, sit in the prime listening position and have someone
switch between the compensation choices,using well recorded dialogue or
musical instrument recordings. Choose whichever switch position sounds
most natural and real to you.
NOTE: Although these controls have been designed to compen-
sate for various acoustic room anomalies, we recommend that you
try them to hear the difference that they make in the sound of the
system. For any number of reasons, you may decide that you prefer
them set in a particular manner inconsistent with your room's acous-
tics, but sounds best to you. Experiment. It will be worth it.
System Setup
This control
High Frequency Energy
changes the tilt or roll-off slope of the
tweeter. It has been designed to help com-
pensate for different room acoustics. The
THX/ Average position is intended for
rooms with a reasonable combination of
reflective (hard) and absorptive (soft) sur-
HF
LF
This control "shelves up" the
Location
upper midrange and high frequency
HF
energy from the speaker in the position
marked Behind Screen. This is to com-
pensate for the reduction of these frequen-
LF
cies when they are partially blocked by the
materials in front of them if the speakers
HF
LF
Use this switch
Boundary Compensation
to adjust the lower midrange output of the
speaker to compensate for the typical
sound colorations caused by placing the
speaker close to a TV screen or building it
into a wall unit or cabinet.
9
��
���
���
����
��� �
��
���
���
����
��� �
����
����
����
������
��� ���
��