Atlas IHVP Specifiche tecniche - Pagina 2
Sfoglia online o scarica il pdf Specifiche tecniche per Altoparlanti Atlas IHVP. Atlas IHVP 2. Compliant horn loudspeaker system powered by cisco poe network switches
Anche per Atlas IHVP: Opuscolo e specifiche (4 pagine)
Stampa la pagina*IPS-ZC1 interfaces to PA601 amplifier in IDF/MDF location. PA601
amplifier will power a single zone of up to (40) APF-15T loudspeakers
set to 1 watt power tap each. This configuration will to provide up to
80dB SPL @ 50' from each APF-15T device in the zone.
Unit shall be Atlas Sound Model IHVP. The loudspeaker system shall
include factory assembled horn loudspeaker, IP addressable PCB
amplifier/control and cast aluminum alloy baffle. Loudspeaker shall be
Atlas Sound Model APF-15. Unit shall be double re-entrant type with
compression driver mounted within vandal-resistant housing. Audio
power capability shall be 15 watts continuous. Frequency response
shall be 600-14,000 Hz (nominal), 700-5,500 Hz (± 5 dB). Sound
pressure leval shall be 104 dB (1 W / 1 M). Sound dispersion angle
shall be 95°. Loudspeaker mounting shall be by eight .1875" (4.76 mm)
evenly spaced holes. Model APF-15 dimension shall be 5
Dia. x 3.4375" (87 mm) Deep with 6.9375" (176 mm) Dia. flange. Finish
shall be grey baked epoxy. The IP addressable PCB amplifier/control
shall be mounted to the rear of the loudspeaker baffle via concealed
weld studs. The amplifier/control PCB shall be capable of producing
9 watts RMS with a minimum of 9VDC power provided either locally
APF-15 LOUDSPEAKER SPECIFICATIONS
Power Handling
Sensitivity
Frequency Response
Dispersion
Dimensions
Finish
BAFFLE SPECIFICATIONS
Baffle Material
Speaker Grille Material
Overall Dimensions
Color
AMPLIFIER/CONTROLLER SPECIFICATIONS
Power Rating
Inpute
Outputs
Power Source
Dimensions
Mounting
Network Control
1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A.
TELEPHONE: (800) 876-3333 / FAX (800) 765-3435
© 2008 Atlas Sound LP
ARCHITECT AND ENGINEER SPECIFICATIONS
⁄
" (143 mm)
5
8
15 W continuous
120 dB at 15 W (peak) 114 dB at 15 W / 1 M (avg) 700-5,500 Hz
104 dB 1 W / 1 M (avg) 700-5,500 Hz
600-14,000 Hz (nominal) 700-5,500 Hz (±5 dB)
95° (-6 dB, 2000 Hz octave band)
5
⁄
" Dia. x 3
⁄
" D x 6
⁄
" Dia. Flange
5
7
15
8
16
16
Grey baked epoxy
Cast aluminum
22-gauge perforated stainless steel
10.75" (273 mm) square x 1" (25 mm) deep
White
9 watts RMS into 8 Ω load with 9VDC In
RJ-45 female on PCB accessible from rear of baffle
2 wire main ± terminated to loudspeaker
Cisco IEEE 802.3AF compliant POE network switches or local 12-18VDC PSU
4.25" (108 mm) by 7.25" (184 mm)
4 holes to weld studs on baffle (factory assembled)
Berbee InformaCast on multicast enabled networks
Specifications subject to change without notice
Printed in U.S.A.
ENCLOSURE IS NOT INCLUDED.
MODEL
DESCRIPTION
SEST-IH
Surface mount, straight enclosure for IVHP, stainless steel
construction, neutral white finish
FEST-IH
Flush mount straight enclosure for IHVP, stainless steel
construction, no finish
or via Cisco IEEE 802.3AF compliant POE switches. Interconnect
shall be via female RJ-45 connector mounted to the PCB. All control
functionality of the PCB amplifier shall be determined via software. The
metal loudspeaker baffle overall dimensions shall be 12.88" (327 mm)
wide by 14.38" (365 mm) tall. Construction shall be cast from self-aging
aluminum alloy with a tensile strength of 44,000 P.S.I. Assembly shall
include provisions to mount the re-entrant horn. 22-gauge perforated
stainless screen shall be spot welded over the loudspeaker cut-out.
Flush-mounting tamperproof heat-treated alloy screws and a special
wrench shall be furnished. Dimensions shall be 10.75" (237 mm)
square by .75" (19 mm) deep (not including weld stuf depth.) Baffle
finish shall be textured white epoxy. Optional enclosures shall include
white stainless steel surface mount model SEST-IH and flush mount
model FEST-IH (unfinished.)
AtlasSound.com
00506
ATS002381 RevB 1/08
Available optional enclosures:
SL1-2089