Bose FreeSpace ZA 2120-LZA Manuale di installazione e funzionamento - Pagina 42
Sfoglia online o scarica il pdf Manuale di installazione e funzionamento per Amplificatore Bose FreeSpace ZA 2120-LZA. Bose FreeSpace ZA 2120-LZA 48. Integrated / zone amplifiers
Stampa la pagina
- 1. Table of Contents
- 2. Freespace® Iza 2120-Lz / Iza 2120-Hz Integrated Zone Amplifier
- 3. Iza 2120-Lz Rear Panel
- 4. Za 2120-Lza/Hza Rear Panel
- 5. Remote Volume Control
- 6. Connecting the CC-1 to a Freespace® Amplifier
- 7. Connecting an Iza 2120-Lz/Hz Amplifier to a Za 2120-Lza/Hza Amplifier
- 8. Troubleshooting
Technical Information
Troubleshooting
Problem
• No power
• Power is on, but no
sound
• Power is on, but sound
is low
• Sound is distorted
• Unnatural sound
42 - Installation Guide
What to do
• Turn on power. Blue LED on front-panel will be visible when power is on.
• Make sure the power cord is plugged in.
• Try a different AC outlet that is working with another piece of equipment.
• Make sure the input source is turned on.
• Verify that there is an input signal from the source.
• Check the cable connections from the source to the amplifier.
• Ensure the desired source (A/B) is selected on the front panel.
• If a user interface is connected to the REMOTE connector on the rear panel, make sure the desired
source (A/B) is selected on user interface (user interface overrides the front-panel source select).
• Make sure the MASTER LEVEL control is turned up.
• If a user interface is connected to the REMOTE connector on the rear panel, make sure the volume
control on the user interface is turned up (user interface overrides the front-panel MASTER LEVEL
control).
• Make sure a 1/8" (3.5 mm) TRS input cable is not connected to the AUX INPUT.
• The AUX INPUT has a mechanical override feature so if an input cable is connected to it the
selected Input A/B source will be automatically overridden - even if the AUX INPUT audio source is
not playing or connected.
• If a contact closure is connected to the MUTE connector on the rear panel, check the switch to
ensure the mute function has not been triggered.
• If a source is connected to the PAGE INPUT connector on the rear panel, make sure it has not been
triggered.
• Make sure loudspeakers are connected properly.
• Make sure that loudspeaker taps are set correctly. See "Loudspeaker Usage" on page 33.
• Check that the amplifier has adequate ventilation. Improper ventilation could cause the amplifier to
go into protection mode and no audio will be heard.
• Ensure that the output wiring is correct. A short circuit will cause the amplifier to go into
protection mode and no audio will be heard.
• Verify that the audio input source output is turned up to a nominal level.
• Check the cable connections from the source to the amplifier.
• Increase input level of source with GAIN controls on amplifier. Turn GAIN knob clockwise until you
start seeing a red INPUT SIGNAL CLIP LED on front-panel. Then turn GAIN counter-clockwise until
the LED turns green.
• Make sure OUTPUT TRIM controls on amplifier are not turned down too low.
• If a user interface is connected to the REMOTE connector on the rear panel, make sure the volume
control on the user interface is turned up (user interface overrides the front-panel MASTER LEVEL
control).
• Make sure that loudspeaker taps are set correctly. See "Loudspeaker Usage" on page 33.
• Verify that the INPUT SIGNAL CLIP LED on the front-panel is not red. If it is red, reduce the source
output level or reduce the input gain.
• If the input source signal is clean, verify that the loudspeakers are not overdriven or damaged.
Check the loudspeaker tap setting.
• Verify that the proper EQ preset is selected for the loudspeakers being used. With the IZA 2120-
HZ, use the HPF setting for loudspeakers other than FreeSpace
their own EQ settings.
• Check the TREBLE and BASS controls on the front-panels.
pro.Bose.com
loudspeakers and those that have
®