DRYDEN AQUA DA-GEN Manuale d'uso - Pagina 12

Sfoglia online o scarica il pdf Manuale d'uso per Inverter DRYDEN AQUA DA-GEN. DRYDEN AQUA DA-GEN 13.
Anche per DRYDEN AQUA DA-GEN: Manuale d'uso (9 pagine)

Stampa la pagina

1. Troubleshooting

F.1

F.2

F.5

F.6

F.9

F.10

G.2 Gas (0) - The FL1 alarm is only activated by cell's gas sensor (external flow switch annulled).

G.1

G.2

Siempre ON (1) - The FL1 alarm is never activated (invalidates cell's gas sensor and external flow switch);

Paddle (2) - The FL1 alarm is activated by external flow switch (gas sensor annulled).

Paddle or gas (3) - When both cell's gas sensor and external flow switch are connected, and either of them detects lack of

flow, The FL1 alarm is activated. To connect the external flow switch use the FL1 terminal

Paddle + Gas (4) - When both cell's gas sensor and external flow switch are connected, and both of them detects lack of

flow, The FL1 alarm is activated. To connect the external flow switch use the FL1 terminal

Paddle delay - Delay before FL1 is activated

Relay control through flow detection - Manage the FL1 alarm deactivation in case of lack of flow. Recommended option

for floculant dosification or similar.

H.1

H.2

I.1

I.2

I.2 Node addr: Used for the configuration of more than 2 user interfaces.

For normal operation of the system, keep the value to 1 for this parameter.

K.1

K.2

K.2 Server control and connection port in case there is WIFI Module connected to the system.

For the proper functioning of the system, do not change the default values unless you receive a notice from your provider.

F) DOSING PUMPS

F.3

F.7

F.10 You can associate the level sensor (TANK) to the pH or chlorine (rX). This menu corresponds to the behavior of

the system after the TANK signal activation (acid deposit level TANK).

Ignore – TANK is not shown in the display

Inform – When the sensor detects that the level is low, the TANK alarm is displayed.

Force stop – When the sensor detects that the level is low, the TANK alarm is displayed and the associated dosing

pump stops.

G) EXTRA SETTINGS

H) COUNTERS

H.3

H.2 Reset counters: There are two levels of working hours counters which log the

working hours of the components and devices.

In this service menu the installer can reset the working hour counters on the first

level (for example when a new cell is installed).

The second level of the working hour counters can only be accessed by the factory.

I) CONNECTION

K) WEB IP

F.2 There are 2 modes for the pH dosing pump:

F.4

F.3 Normal: Delay - Delay time between detection of incorrect

value and the start of dosing.

F.4 Repetitive: With the two timers you can programm the ON

and OFF time of the dosing pump

Scaling: Proportional reduction of the dosing time (Pump On

time) when getting close to the setpoint. Example 100%: The

pump time is reduced proportionally if the pH is closer than

1 to the setpoint. Example 50%: The pump time is reduced

proportionally if the pH is closer than 0.5 to the setpoint.

F.8

F.6 Other pumps: With the two timers you can programm the

ON and OFF time of the dosing pump

F.8 It corresponds to the behavior of the system after AL3

activation:

Ignore – AL3 is not shown in the display.

Inform – After the selected interval, the AL3 alarm is displayed.

Force stop – After the selected interval, the AL3 alarm is

displayed on the display and the dosing pump stops. To reset

the alarm and the dosing pump, press