AirTime AT12RPS Manuale d'installazione e d'uso - Pagina 2
Sfoglia online o scarica il pdf Manuale d'installazione e d'uso per Orologio AirTime AT12RPS. AirTime AT12RPS 4. Solar powered wall clock
Anche per AirTime AT12RPS: Manuale d'installazione e d'uso (6 pagine)
Stampa la paginaAirTime Solar Wall Clock
THIS EQUIPMENT COMPLIES WITH FCC CLASS-B REQUIREMENTS
PURSUANT SUBPART J OF PART-15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARNING: Changes or modifications to this product not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body. This Transceiver must not be co-located or
operating in conjunction with any other antenna or Transceiver.
Disclaimer
The information within this document has been carefully checked and is
believed to be entirely reliable. However, no responsibility is assumed for
inaccuracies. Lathem Time Corp. reserves the right to make changes to any
products herein to improve reliability, function, or design.
AirTime, Lathem and the Lathem logo are registered trademarks of Lathem
Time Corporation. Other product names mentioned in this manual may be
trademarks of their respective companies and are hereby acknowledged.
WARNING: Changes or modifications to this product not expressly approved by
the party responsible for compliance could void the user's authority to operate
this equipment.
Copyright © 2009 Lathem Time Corporation. All rights reserved.
Lathem Time Corporation
200 Selig Drive SW
Atlanta, GA 30336
www.lathem.com
Document No. USG0080 / Revised April 14, 2009
Page 2
Doc. No. USG0080
during normal operation. To verify that the clock has properly
received an AirTime signal:
1. Press the A button the back of the clock
2. Look at the LED on the front of the clock
a. Green: Signal was received successfully
b. Red: Signal was not received.
The LED on the front of the clock will flash
if the signal is not received within the previous 72 hours.
Setting the Time Manually
If the AirTime transceiver is not installed and transmitting, you
can manually set the time on the clock and it will operate as a
highly precise standalone clock until an AirTime signal is
received.
1. Press and hold the B button on the back of the clock for 5
seconds, until the red second hand stops.
2. Press the A button on the back of the clock to advance the
time one minute. You can press and hold the A button to
rapidly advance the minute and hour hands.
3. When the time on the clock is one minute before the
current time, wait until the exact time reaches zero "0"
seconds and then press the B button on the back of the
clock.
4. The clock will begin normally operation.
Patent Pending
Installation & User's Guide
Red
automatically
Page 7