Atsumi Electric NR60AQM Istruzioni per l'installazione
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Sensori di sicurezza Atsumi Electric NR60AQM. Atsumi Electric NR60AQM 2. Photoelectric beam detector, 200ft./400ft./660ft. / 60m/120m/200m range
4-2-2 SHIN-MIYAKODA, KITAKU, HAMAMATSU, SHIZUOKA 431-2103 JAPAN
PHONE: +81-53-428-4116 FAX: +81-53-428-4119
PHOTOELECTRIC BEAM DETECTOR
NR60AQM :200ft./ 60m Range
NR120AQM:400ft./120m Range
NR200AQM:660ft./200m Range
INSTALLATION INSTRUCTIONS
1 GENERAL DESCRIPTION
The NR60AQM/120AQM/200AQM are quad photoelectric detectors designed to activate an alarm output upon the detection of intruder through 4 pulsed infrared
beams .
For stable operation, the NR60AQM/120AQM/200AQM are equipped with the following features.
- 100 Times Sensitivity Allowance
Stable operation is maintained even if 99% of beam energy is lost by rain, fog, frost, etc.
- Quad Beam Detection (AND/OR GATE Selectable)
AND GATE : All four beams need to be blocked simultaneously to trigger an alarm, resulting less false alarms caused by birds and other small animals.
OR GATE : Eather of Upper Two Beams or Lower Two Beams need to be blocked, resulting the detection of crawl through on the ground.
- Beam Power Control
This function allows selection of the appropriate beam intensity relative to the detection range to minimize the risk of reflection on the nearby walls and cross-taking
with other detectors.
- Beam Interruption Time Control
This feature can be used to change the beam interruption time to best fit the application.
- Stackable
The selectable beams up to 8 kinds can be used and it can allow to stack NRAQM up to 4 units for the high density beam barrier.
4 COMPONENTS
CHASSIS
DETECTOR
CHASSIS
MOUNTING
HOLE
TERMINALS
WIRE HOLE
CHASSIS
MOUNTING
HOLE
WIRE HOLE
UNIT MOUNTING
Transmitter has 5 terminals.
SCREW
Receiver has 9 terminals.
6 WIRING
6.1 TERMINALS
TRANSMITTER
RECEIVER
POWER (non-polarized)
POWER (non-polarized)
10.5 - 28.0VDC
10.5 - 28.0VDC
Tamper Output (1b)
30VDC 0.1A
ALARM Output (1c)
SYNCHRO
30VDC 0.2A
EDC Output (1b)
30VDC 0.2A
Tamper Output (1b)
30VDC 0.1A
6.2 WIRING LENGTH (MAX ONE WAY LENGTH)
MAXIMUM DISTANCE (m)
WIRE
NR60AQM
NR120AQM
NR200AQM
GAUGE
12VDC
24VDC
12VDC
24VDC
12VDC
AWG22
90
820
80
790
80
AWG19
170
1,600
170
1,550
160
AWG17
320
2,930
310
2,830
300
AWG14
570
5,150
550
4,980
530
* This chart is based on 1 set connected to the same wire run from the power
source.
* When installing 2 or more sets on one wire, the max length is obtained by
dividing the max wire length listed above by the number of sets installed.
8 FEATURES
8.1 SELECTABLE BEAMS
Crosstalking will occur when using multiple beams for stack beam or long
distance application, which can cause no-alarm problems.
This NR-AQM series has selectable beams up to 8 kind (2 Groups × 4
Channels) which can be used to avoid crosstalking.
8.2 SELECTABLE AND/OR GATE
The unit has photoelectric intrusion detection system designed to provide an
alarm relay activation upon the detection of an intruder moving through four
pulsed infrared beams (AND GATE), and also moving through either of the
upper two beams or the lower two beams (OR GATE).This AND/OR GATE is
selectable with the dip switches for required protection.
8.3 EDC (Environmental Discrimination Circuit)
EDC sends EDC signal when it becomes difficult to maintain stable operation
due to environmental disturbance like fog or rain.
There are two selective features in utilizing the Bypass switch at the receiver.
Hereunder, the condition where it is difficult to maintain stable operation for
more than 3 seconds due to unfavorable environmental condition is defined as
"Poor Environmental Condition".
BYPASS switch =====> OFF
1) In Poor Environmental Condition
EDC LED will turn on and EDC signal will be provided through the normal
closed relay output at the receiver.
The alarm signal will then be generated by the further loss of the beam
energy.
2) When either optical module is blocked for 3 seconds
EDC LED will turn on and EDC signal will be provided. No alarm output
will be generated.
3) When both optical modules are blocked for 3 seconds
After the specified interruption time, alarm LED turns on and alarm signal
is generated. If beams are blocked for more than 3 seconds, EDC LED
will turn on and EDC signal will be provided.
BYPASS switch =====> ON
1) In Poor Environmental Condition
EDC LED will turn on and EDC signal will be provided through the normal
closed relay output at the receiver.
With the further loss of beam energy, the alarm LED turns on but alarm
signal is NOT generated (alarm relay is automatically shunted).
2) When either optical module is blocked for 3 seconds
EDC LED will turn on and EDC signal will be provided. If another optical
module is blocked, alarm LED turns on but no alarm signal is generated.
3) When both optical modules are blocked for 3 seconds
After the specified interruption time, alarm LED turns on and alarm signal
is generated. Even if the beams are blocked for more than 3 seconds,
EDC LED will not turn on and EDC signal is not provided.
Note : It is extremely important to have the EDC connected to a trouble circuit.
It is also important to check the system any time the EDC relay has been
activated.
Note : EDC feature has not been evaluated by UL.
We appreciate your purchase of ATSUMI PHOTOELECTRIC DETECTORS.
Please read the following installation instructions carefully for appropriate use of
the product.
COVER
LENS (UPPER)
SCOPE (UPPER)
VERTICAL ADJUSTMENT
SCREW (UPPER)
HORIZONTAL ADJUSTMENT
SCREW (UPPER)
OPERATION PART
HORIZONTAL ADJUSTMENT
SCREW (LOWER)
VERTICAL ADJUSTMENT
SCREW (LOWER)
LENS (LOWER)
SCOPE (LOWER)
COVER MOUNTING
SCREW
6.3 EXAMPLES
1 SET
POWER
output
ALARM
input (NC)
Control Panel
Receiver
Transmitter
2 SET
POWER
output
ALARM
input (NC)
Control Panel
24VDC
Receiver
Transmitter
770
1,500
Note: * Do not supply power until all wiring is completed.
2,740
* Power is to be provided by a UL Listed burglar alarm power supply or
4,820
burglar alarm control panel.
* Refer to the National Electrical Code, NFPA70.
* This system should be tested at least once a week to ensure proper
function.
* Don't wire aerial.
* Use pipes for outdoor wiring.
8.4 BEAM INTERRUPTION TIME
The beam interruption time defines the amount of time an intruder must be in the
beam path before an alarm is output. For instance, if the interruption time is set at
100msec, the detector output an alarm only if the beams are blocked for more
than 100msec.
8.5 BEAM POWER CONTROL
The beam strength is at optimal level if used at the maximum range.
If used for shorter distance, excess beam energy reaches the receiver, resulting in
reflection on the nearby walls and cross-talking with other detectors.
Max Detection Range
Beam energy decreases as it flies a
long distance.
For shorter range, more beam energy
reaches the receiver.
Short Range
8.6 LEVEL LED
One LED displays the amount of beams received during optical module
adjustment.
As more beam energy is received, the illumination time shortens as follows:
ON OFF once OFF twice OFF three times Flashing ON three times
ON twice ON once OFF.
When the LED turns off, the alignment is complete.
LEVEL LED
ON
OFF once
OFF twice
OFF three times
Flashing
ON three times
ON twice
ON once
OFF
2 INSTALLATION CONSIDERATIONS
Read the following prior to installing,
wiring and regular maintenance.
DO NOT INSTALL THE UNIT
(1) where trees, plants, of falling leaves will block
the beams.
(2) where intense source of light, sunlight will be
reflected, directly into the receiver optics.
A external light incoming within ±3° angle of
each receiver axis may cause false alarms.
(3) where on movable surfaces.
(4) where subject to foul water or salt water.
(5) where over the max range on each model.
(6) where subject to strong electrical noise or RFI.
(7) where subject to strong vibration or impact.
(8) where subject to corrosive or explosive gas.
3 SUPPLIED PARTS
Make sure the following components are included in the package.
OPERATION PART ON
OPERATION PART ON
TRANSMITTER
RECEIVER
POWER LED
POWER
DIP SWITCH
No.
FUNCTION
OFF
ON
No.
FUNCTION
1
GROUP
A
B
1
GROUP
M
1
2
3
M
1
2
OFF OFF
ON
ON
2
OFF OFF
3
OFF
ON
OFF
ON
BEAM POWER
3
OFF
ON
4
4
AND/OR
AND
5
BYPASS
CONTROL
6
LEVEL
LOWER
130
160
CHECK
BEAM
260
320
100
180
150
200
200
360
100
OUTDOOR 60
200
75
INDOOR 120
400
BEAM POWER
40
CONTROL(m)
INTERRUPTION
TIME(msec)
TESTER LEVEL
HIGH DENSITY
3.4V~: EXCELLENT
3.0V~: GOOD
0.0V~: POOR
CONNECTION
7 MOUNTING
7.1 POLE MOUNTING
- Choose an appropriate mounting location for the system. Install the poles with a clear line-of-sight
between the transmitter and the receiver.
- Loosen the transmitter's cover mounting screw and remove the cover.
- Loosen the 2 unit mounting screws and remove the chassis by sliding it down against the unit.
- Attach the mounting plates to the chassis with the clamping screws (short) (see FIGURE 1).
- Firmly attach the chassis to the poles with the U-clamps and the screws (long) (see FIGURE 2).
Make sure the transmitter is mounted in direct line-of-sight with the receiver.
- Route wiring through the chassis wire hole, leaving enough wire to access the transmitter's terminal
strip.
- Route wiring through the transmitter's wire hole.
- Slide the transmitter onto the chassis. Tighten with the unit mounting screws.
- Repeat this mounting process for the receiver. Make sure it is mounted in direct line-of-sight with
the transmitter.
- Wire to the terminal strips. (Refer to the 6. WIRING)
- Keep more than 10mm space around the chassis as this detector is bigger than it.
- Use the knockout at the bottom of this detector for the surface wiring.
Pole Diameter
38.0 - 42.7mm
Receiver
Transmitter
7.2 WALL MOUNTING
- Loosen the transmitter's cover mounting screw and remove the cover.
- Loosen the 2 unit mounting screws and remove the chassis by sliding it down against the unit.
- Route wiring through the wire hole of the chassis. Leave enough wire to access the transmitter's
terminal strip.
- Mount the chassis to the mounting surface with the chassis mounting screws.
- Route wiring through the wire hole of the transmitter. If surface mounting is used, knock-out the
thin-wall wire hole at the bottom of the transmitter.
- Reattach the transmitter to the chassis.
- Repeat this mounting procedure for the receiver. Make sure it is mounted in direct line-of-sight with
the transmitter.
- Wire to the terminal strips. (Refer to the 6. WIRING)
8.7 HIGH DENSITY
(This is a special feature for stacking gates.)
- By connecting HIGH DENSITY CONNECTION (OUT) of the receiver [1] and HIGH DENSITY CONNECTION (IN) of the receiver [2], AND GATE can
be formed between the lower beam of the receiver [1] and the upper beam of the receiver [2].
Alarm is output to the receiver [2].
- By connecting HIGH DENSITY CONNECTION (OUT) of the receiver [2] and HIGH DENSITY CONNECTION (IN) of the receiver [3], AND GATE can
be formed between the lower beam of the receiver [2] and the upper beam of the receiver [3].
Alarm is output to the receiver [3].
- Up to 8 units can be connected.
- Only alarm operations are interlinked.
Other features including the EDC function independently in each of the receivers.
Caution : All of the receivers to be connected must have AND GATE setting and the same sensitivity.
- Connecting high density connection cables
Connect the high density connection cables that come with the product.
Caution : The length of these cables must be within 2m.
Caution : The connection of OUT and IN must be made 1 to 1, and do not connect them in parallel.
Transmitter [1]
Transmitter [2]
Transmitter [3]
Symbol
Indicate that incorrect operation causes significant danger of accident resulting in
WARNING
death or serious injury to the user.
Indicate that incorrect operation causes possibility of injury to the user or damage to
CAUTION
the unit.
CAUTION
AVOID
(1) extreme temperature and humidity.
(2) magnets or any magnetized material.
(3) running power and output wires near high
voltage power sources.
(4) the beam interference between other units
when multiple units are installed as this beam
spread angle is 1.4 degree.
IMPORTANT
(1) Face upper/lower optical modules on the
transmitter and receiver towards each other.
(2) Be sure of the beam in alignment optical
modules can be adjusted within ±90°
horizontally and ±10° vertically.
PARTS
Transmitter, Receiver
Installation Instructions
U-clamp
Mounting Plate
5 BEAM SPREAD
The beam spread angle is ±0.7° .
Refer to the right table and the
diagrams below to determine the
installation conditions.
ALARM LED
EDC LED
ALARM
LEVEL LED
EDC
LEVEL
DIP SWITCH
OFF
ON
A
B
2
3
ON
ON
OFF
ON
SENSITIVITY VOLUME
OR
OFF
ON
(INTERRUPTION TIME)
UPPER
BEAM
300
400
500
ALIGNMENT
ALIGNMENT CHECK
CHRCK
TERMINALS
TERMINALS
Transmitter
Back-to-back
Pole Mounting
Receiver [1]
OUT
Receiver [2]
IN
Intruder
Alarm
OUT
Receiver [3]
IN
Meaning
WARNING
Do not perform installation and wiring when it
thunders.
Do not supply power until all wiring is completed.
Keep power between 10.5~28 VDC anytime.
Do not disassemble or modify the unit.
PCS
PARTS
PCS
2
Clamping Screw (short 4×8mm)
8
1
Clamping Screw (long 4×25mm)
8
4
Chassis Mounting Screw (5×16mm)
8
4
High Density Connection Cables 2P
2
Distance (A)
Spread (B)
Spread (C)
20m
0.5m
0.8m
40m
1.0m
1.3m
60m
1.5m
1.8m
80m
2.0m
2.2m
100m
2.5m
2.7m
120m
3.0m
3.2m
140m
3.5m
3.7m
160m
4.0m
4.2m
180m
4.5m
4.7m
200m
5.0m
5.2m
B
C
Receiver
A
FIGURE 1
Mounting Plate
Clamping
Screw
(short)
FIGURE 2
U-clamp
Clamping
Screw
(long)
Knockout
Chassis
Chassis
Mounting
Screws
(included)
Wire Hole
Knockout
Unit Mounting
Screws
Receiver [1]
IN
OUT
Receiver [2]
IN
OUT
Receiver [3]
IN
OUT