Absolute Process Instruments APD 6010 Manuale di avvio rapido - Pagina 2
Sfoglia online o scarica il pdf Manuale di avvio rapido per Trasmettitore Absolute Process Instruments APD 6010. Absolute Process Instruments APD 6010 2. Ac to dc transmitters, isolated, factory configured
Installation and Setup
Precautions
WARNING! All wiring must be performed by a qualified electri-
cian or instrumentation engineer. See diagram for terminal
designations and wiring examples. Consult factory for assis-
tance.
WARNING! Avoid shock hazards! Turn signal input, output, and
power off before connecting or disconnecting wiring, or remov-
ing or installing module.
Précautions
ATTENTION! Tout le câblage doit être effectué par un élec-
tricien ou ingénieur en instrumentation qualifié. Voir le dia-
gramme pour désignations des bornes et des exemples de
câblage. Consulter l'usine pour assistance.
ATTENTION! Éviter les risques de choc! Fermez le signal
d'entrée, le signal de sortie et l'alimentation électrique avant
de connecter ou de déconnecter le câblage, ou de retirer ou
d'installer le module.
API maintains a constant effort to upgrade and improve its products.
Specifications are subject to change without notice. See api-usa.com for
latest product information. Consult factory for your specific requirements.
WARNING: This product can expose you to chemicals includ-
ing nickel, which are known to the State of California to cause
cancer or birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
Electrical Connections
Polarity must be observed for output wiring connections. If the
output does not function, check wiring and polarity.
See wiring diagrams at right. Observe polarity. If the output
does not function, check wiring and polarity.
*
Do not make any connections to unused terminals or use
them as wiring junctions for external devices. This may cause
permanent damage to the module!
Each product is factory configured to your exact input and
output ranges as indicated on the serial number label.
Input
For an AC signal is it not necessary to observe polarity when
connecting the input.
Connect the AC signal input to terminals 9 and 11 as shown in
the wiring diagram.
Type of Input Device
Terminal
Device with an AC voltage or
9
AC milliamp output.
Voltage Output
If your receiving device (such as a PLC or a display) uses a
voltage input, use terminals 3 and 4 as shown in the wiring
diagram.
Current Output
Determine if your receiving device (such as a PLC or a display)
provides power to the current loop or if the loop must be pow-
ered by the APD module. Typical voltage may be 9-24 VDC at
your device's input terminals if it provides power to the loop.
If your device does not power the current loop, the APD can
provide power using terminals 3 and 4 as shown as shown in
the wiring diagram.
If it provides power to the loop or an external supply provides
power to the loop, use terminals 2 and 3 as shown as shown
in the wiring diagram.
Type of Device for Output
– Terminal
Measuring/recording device
3 (–)
accepts a voltage input.
Measuring/recording device
accepts a mA (current) input
and the input is unpowered or
3 (–)
passive. APD module provides
the loop power.
Measuring/recording device
accepts a mA (current) input
2 (–)
and provides power to the
current loop.
Module Power
Check model/serial number label for module operating voltage
to make sure it matches available power.
When using DC power, either polarity is acceptable, but for
consistency with similar API products, positive (+) can be wired
to terminal 13 and negative (–) can be wired to terminal 16.
The power supplies are fuse protected and the unit may be
returned to API for fuse replacement.
A
A
P
P
BSOLUTE
BSOLUTE
ROCESS
ROCESS
Mounting to a DIN Rail
Install module vertically on a 35 mm DIN rail in a protective
enclosure away from heat sources. Do not block air flow. Allow
1" (25 mm) above and below housing
vents for air circulation.
1. Tilt front of module downward and posi-
tion against DIN rail.
2. Clip lower mount to bottom edge of
DIN rail.
3. Push front of module upward until
upper mount snaps into place.
Removal
1. Push up on the bottom back of the
module.
2. Tilt front of module downward
to release upper mount from top
edge of DIN rail.
3. The module can now be removed from
the DIN rail.
Calibration
Input and output ranges are factory pre-
configured (at 24°C ±1°C). Front-mounted Zero and Span
potentiometers are used to calibrate the output to compensate
for load and lead variations.
1. Apply power to the module and allow a minimum 20 minute
warm up time.
2. Using an accurate calibration source, provide an input to
the module equal to the minimum input required for the
application.
3. Using an accurate measurement device for the output,
adjust the Zero potentiometer for the exact minimum output
desired. The Zero control should only be adjusted when the
input signal is at its minimum. This will produce the cor-
responding minimum output signal. For example: 4 mA for
a 4-20 mA output or –10 V for a ±10V output.
4. Set the input at maximum and adjust the Span pot for the
exact maximum output desired. The Span control should
only be adjusted when the input signal is at its maximum.
Terminal
This will produce the corresponding maximum output
signal. Example: for 4-20 mA output, the Span control will
11
provide adjustment for the 20 mA or high end of the signal.
5. Repeat adjustments for maximum accuracy.
Output Test Function
When the Test button is depressed it will drive the output with a
known good signal that can be used as a diagnostic aid during
initial start-up or troubleshooting. When released, the output
will return to normal.
The Test Cal. potentiometer is factory set to approximately
50% output. It can be adjusted to set the test output from 0 to
100% of the output span. Press and hold the Test button and
adjust the Test Cal. potentiometer for the desired output level.
Operation
The APD 6010 accepts an AC voltage or current input and
provides an optically isolated DC voltage or current output that
is linearly related to the input.
The green LoopTracker
that a signal is being sensed by the input circuitry of the mod-
+ Terminal
ule. It also indicates the input signal strength by changing in
intensity as the process changes from minimum to maximum.
4
(+)
If the LED fails to illuminate, or fails to change in intensity as
the process changes, check the module power or signal input
wiring. Note that it may be difficult to see the LEDs under bright
4
(+20 V)
lighting conditions.
The red LoopTracker output LED provides a visual indication
that the output signal is functioning. It becomes brighter as
the input and the corresponding output change from minimum
to maximum.
3
(+)
For current outputs, the red LED will only light if the output loop
current path is complete. For either current or voltage outputs,
failure to illuminate or a failure to change in intensity as the
process changes may indicate a problem with the module
power or signal output wiring.
I
I
NSTRUMENTS
NSTRUMENTS
Upper
Mount
Lower
Mount
Spring
Clip
input LED provides a visual indication
®
1220 American Way Libertyville, IL 60048
Phone:
800-942-0315
Fax: 800-949-7502
APD 6010
1
2 3 4
Output
5 6
7 8
Output Test
* Do not make
connections to
unused terminals!
Wire terminal
torque
0.5 to 0.6 Nm or
4.4 to 5.3 in-lbs
Input
9
1 0
1 1
1 2
Power
1 3 1 4
1 5
1 6
Voltage Output
mA output: determine if receiving device has a passive or powered
input. The module can be wired for a sinking or sourcing mA output.
Loop
3- or 4-wire transmitter
or 2 wire transmitter with
Supply
external power supply
–
+
Sinking mA Output
Module mA output is unpowered
Sourcing mA Output
Module powers mA output loop
External Contact
for Test Function
Variable Brightness
Output Indicator
Output Test Level
Adjustment
Test Cal.
Push to Test
Output
Output Span
Calibration
Variable Brightness
Input Indicator
Isolated Transmitter
Output Zero
Calibration
mVAC,
AC Signal Input
VAC or
mAAC
* Do not make connections
to unused terminals!
13
Cu 60/75°C
13 Power AC or DC +
conductors
14
Earth Ground
14 AWG
16 Power AC or DC –
max.
To maintain full isolation avoid combining power supplies
in common with input, output, or unit power.
api-usa.com
Voltage
Device
–
+
1
2
3
4
mA
Device
R
i
+
–
–
+
1
2
3
4
mA
Device
R
i
–
+20V
1
2
3
4
5
6
7
8
Output
Loop
Tracker
Test
Span
Input
Loop
Zero
Tracker
APD 6010
AC to DC
9
10
11
12
14
15
16