3onedata IES5024-2F-P Manuale d'uso - Pagina 5

Sfoglia online o scarica il pdf Manuale d'uso per Interruttore 3onedata IES5024-2F-P. 3onedata IES5024-2F-P 6. Managed industrial ethernet switch ies5024 series

Stampa la pagina

【Installation】

Before installation, confirm that the work environment meet the

installation require, including the power needs and abundant

space. Whether it is close to the connection equipment and other

equipments are prepared or not.

1. Avoid in the sunshine, keep away from the heat fountainhead or

the area where in intense EMI.

2. Examine the cables and plugs that installation requirements.

3. Examine whether the cables be seemly or not (less than 100m)

according to reasonable scheme.

4. Power: 100-240VAC/DC power input

5. Environment: working temperature: -40～75℃

Storage Temperature: -40～85℃

Relative humidity 5%～95%

Rack mount installation

In most of industrial application, it is convenience to use rack

mount installation, the step of installation is as follows:

1. Check if have rack mount installation tools and components

(The package provided parts of components)

2. Check installation place strong or not, have the place to install

the device or not.

3. Put the device into rack, aim at the screw hole of device and

rack, fixed it in strong screw. Easy and convenience to

operation.

Wiring Requirements

Cable laying need to meet the following requirements,

1. It is needed to check whether the type, quantity and

specification of cable match the requirement before cable

laying;

2. It is needed to check the cable is damaged or not, factory

records and quality assurance booklet before cable laying;

3. The required cable specification, quantity, direction and

laying position need to match construction requirements, and

cable length depends on actual position;

4. All the cable cannot have break-down and terminal in the

middle;

5. Cables should be straight in the hallways and turning;

6. Cable should be straight in the groove, and cannot beyond the

groove in case of holding back the inlet and outlet holes.

Cables should be banded and fixed when they are out of the

groove;

7. User cable should be separated from the power lines. Cables,

power lines and grounding lines cannot be overlapped and

mixed when they are in the same groove road. When cable is

too long, it cannot hold down other cable, but structure in the

middle of alignment rack;

8. Pigtail cannot be tied and swerved as less as possible.

Swerving radius cannot be too small (small swerving causes

terrible loss of link). Its banding should be moderate, not too

tight, and should be separated from other cables;

9. It should have corresponding simple signal at both sides of the

cable for maintaining.

【Specification】

Technology

Standard: Support IEEE802.3, IEEE802.3u, IEEE 802.3x,

IEEE802.1Q, IEEE802.1p, IEEE802.1D, IEEE802.1W

Protocol: ARP、ICMP、TCP、UDP、DHCP、DNS、HTTP、

Telnet,、SW-Ring、RSTP、SNMP

Flow control: IEEE802.3x flow control, back press flow control

Function

Switch function: SW-Ring, QOS, 802.1QVLAN, RSTP, SNMP,

Port trunking, static multicast filter, port mirroring,

bandwidth management, broadcast storm control, port

flow statistics, upgrade online, up and download

configuration file, user name access system

SW-Ring: Support Single, Couple, Chain, Dual homing

Exchange attribute

100M forward speed: 148810pps

100M maximum filter speed: 148810pps

Transmit mode: store and forward

Switching fabric capacity: 12.8Gbps

MAC address table: 8K

Memory: 3Mbit

Interface

Electric port: 10Base-T/100Base-TX auto speed control, Half/full

duplex and MDI/MDI-X auto detect

100M optic fiber port: 100Base-FX, SC/ST/FC connector, support

single mode (20/40/60/80Km optional), multi mode

(2Km), wavelength: 1310nm, 1550nm

Console port: debug serial port carry out CLI command

Alarm port: 2 bit terminal block

1 channel relay alarm output (single power series)

2 channel relay alarm output (redundancy power series)

Transfer distance:

Twisted cable: 100M (standard CAT5/CAT5e cable)

Multi-mode: 1310nm, 2Km

Single-mode: 1310nm, 20/40/60Km

1550nm, 80/100/120Km

LED indicator:

Run indicator: Run

Interface indicator: Link (1~24)

Power supply indicator: PWR (1~2)

Alarm indicator: Alarm

Power supply

Input voltage: 100～240VAC/DC

Type of input: 3 bit terminal block

Overload Current Protection: 1.2A

Support single power series and dual supply series of two

products can be optional.

Consumption

IES5024-P (100~240VAC/DC):

Unload consumption: 7.4W