3onedata IES618-4F Manuale di installazione rapida - Pagina 2

Sfoglia online o scarica il pdf Manuale di installazione rapida per Interruttore 3onedata IES618-4F. 3onedata IES618-4F 3. Managed industrial ethernet switch

Stampa la pagina

The product adopts 35mm standard DIN-Rail mounting which

is suitable for most industrial scenes, mounting steps as

follows:

Step 1

Check if the DIN-Rail mounting kit is installed firmly.

Step 2

Insert the bottom of DIN-Rail mounting kit (one side

with spring support) into DIN-Rail, and then insert

the top into DIN-Rail.

Tips:

Insert a little to the bottom, lift upward and then insert

to the top.

Step 3

Check and confirm the products is firmly installed

on DIN-Rail, then mounting ends.

【Disassembling DIN-Rail】

Step 1

Device power off.

Step 2

After lift the device upward slightly, first shift out the

top of DIN-Rail mounting kit, and then shift out the

bottom of DIN-Rail, disassembling ends.

Note before powering on:

Power ON operation: First insert the power supply



terminal block into the device power supply interface,

and then plug the power supply plug contact and power

on.

Power OFF operation: First, remove the power plug,



and then remove the wiring section of terminal block.

Please pay attention to the above operation sequence.

【Power Supply Connection】



DC dual power supply

The device provides 4 pins power supply input terminal blocks

and supports two independent DC power supply systems,

PWR1 and PWR2, which supports non-polarity and

anti-reverse connection function, that the device can work

normally after reverse connection. Voltage range: 12~48VDC.

【Relay Connection】

Relay terminals are a set of normally open contacts of the

device alarm relay. They are open circuit in the state of normal

non alarm, closed when any alarm information occurs. For

example, they are closed when powered off, and send out

alarm. The product supports 1 relay alarm information output

that can output DC power supply alarm information or network

abnormality alarm. It can be connected to alarm light or alarm

buzzer or other switching value collecting devices, which can

timely inform operators when the alarm occurs.

【DIP Switch Settings】

The device provides 4 pins DIP switch for function setting, in

which "ON" is the enabled end. The device needs to be

powered on again to change the status of DIP switch.

DIP switches definition as follows:

DIP

Definition

Operation

Reserved

Upgrade

Set the DIP switch to ON, the

device can be upgraded, then turn

off the DIP switch when this

upgrade completes.

Restore

Set the DIP switch to ON, power

factory

on the device again, it will restore

defaults

to factory settings, then turn off the

DIP switch.

Reserved

【Console Port Connection】

The device provides 1 channel procedure

debugging port based on RS232 serial port, and

can

conduct

device

management after connected to PC. The interface adopts

RJ45 port, the RJ45 pin definition as follows:

Pin No.

definition

【Checking LED Indicator】

The device provides LED indicators to monitor the device

working status with a comprehensive simplified

troubleshooting; the function of each LED is described in the

table as below:

LED

P1/P2

ALM

RUN

Link/Act

(1-8)

【Logging in to WEB Interface】

This device supports WEB management and configuration.

Computer can access the device via Ethernet interface. The

way of logging in to device's configuration interface via IE

browser is shown as below:

Step 1

Configure the IP addresses of computer and the

CLI

command

line

device to the same network segment, and the

network between them can be mutually accessed

Step 2

Enter device's IP address in the address bar of the

TXD

RXD

GND

Indicate

Description

PWR is connected and running

normally

PWR is disconnected and running

OFF

abnormally

Power supply, port link alarm

Power supply, port link without

OFF

alarm

The device is powered on or the

device is abnormal.

The device is powered off or the

OFF

device is abnormal.

Blinking 1 time per second, system

Blinking

is running well.

The

Ethernet

interface

established

active

connection.

The Ethernet interface is in a

Blinking

network activity state.

Ethernet port has not established

OFF

valid network connection

has

network