Atwood MPD 85860 Manuale di installazione e funzionamento

Sfoglia online o scarica il pdf Manuale di installazione e funzionamento per Ricambi per auto Atwood MPD 85860. Atwood MPD 85860 2. Stabilizer jack

Stampa la pagina

ENGLISH, FRANÇAIS

SAFETY ALERT SYMBOLS

Safety Symbols alert you to potential personal safety hazards.

Obey all safety messages following these symbols.

WARNING

avoid possible

injury or death

FOR YOUR SAFETY

READ ALL INSTRUCTIONS BEFORE OPERATING JACKS

Installer:

Provide these instructions to the consumer.

Consumer:

Keep documents for future reference.

Atwood Stabilizer Jacks are designed to be used only on lightweight

campers with a GVWR less than 1,500 lbs. The maximum static load

and lifting capacity is:

Capacity

Stabilizer Jack

PERSONAL INJURY & PRODUCT DAMAGE

Never exceed the rated camper capacity. Camper can collapse

•

or tip over.

Soft or spongy areas may allow jacks to sink, causing camper to

•

tip over. Additional support may be necessary.

Do not place blocks under the jack foot for additional ground

•

clearance.

Put stabilizer jack in stored position before moving camper or trailer.

•

Be sure the drop leg is retracted before releasing stabilizer jack

•

from operating position to storage position to prevent injury from

sudden trailer movement.

INSTALLATION

BOLT ON METHOD: see ➂

1. Use two 3/8˝ - 16 x 3/4˝ Grade 5 hex head cap screws, nut and lock

washer (not furnished).

2. Bolt to trailer side rails, under side rails, or to under side cross

members. Torque bolts 15-20 ft. lbs.

3. For U-bolt stabilizer jack, place the U-bolts over the trailer tongue

frame rail. Slip the ends of the U-bolts thru the stabilizer jack top

plate. Fasten the lock washers over the bolt ends and then the nuts.

Torque the nuts to 25-30 ft. lbs. see -➄

WELD ON METHOD: see ➂

1. Use 1/8˝ fillet weld No. E6011 A.W.S. welding rod (AC or DCRP) 1/8˝

diameter.

2. Machine amps 105-115 with 18-22 volts.

3. Weld full length both sides.

OPERATION

1. Extend leg of jack toward center of trailer.

2. Swing leg downward until the tabs engage in the locking slots-➀.

3. Press on release lever-➀. This will allow the drop leg of the

telescoping jack to slide down to the ground.

4. Insert the jack rod end securely through the holes in the leg and

through the rear hole-➃.

5. Crank the jack rod for desired leveling-➃.

(et Canada)

CAUTION

avoid possible

injury and/or property damage

Lifting

Static

650 lbs.

1,000 lbs.

WARNING

LITERATURE NUMBER

STABILIZER JACK

•Installation •Operation •Maintenance

6. For "U-Bolt" stabilizer jack ONLY, secure coupler to ball of tow

vehicle and remove load from stabilizer jack before proceeding to

step 7.

7. To remove load and store jack:

a. Press down on the release lever for a quick release, or insert

one end of the rod between the release lever and the bottom of

the outer housing for a slower release.

b. Slide the drop leg up into main body.

c. Pull jack toward ground to disengage tabs from slots.

d. Rotate upward until jack snaps into the stored position-➁.

MAINTENANCE

1. Lubricate jack at least every six months in the following manner:

a. Extend jack as far as possible.

b. Clean dirt, mud, tar, etc. from jack.

2. Oil pivot holes and rivet of release lever every six months.

3. Should jack become difficult to operate, clean and oil as detailed in

Step 1 and 2 above, and inspect for bent or worn parts. Use only

factory supplied parts for replacement.

: If it is not possible to get jack to operate freely, replace jack.

NOTE

4. Should problems or questions arise, contact your dealer, the camper

manufacturer, or the Atwood Service Department 574-264-2131.

5. The Stabilizer Jack has a two year warranty from date of purchase

to the original owner. For complete warranty information contact

Atwood before having any work done 574-264-2131.

Locking

Slots

Locking

Tab

Release Lever

Jack Rod

Bolt or Weld

Mounting

Weld

Mounting

Swings

up for

Weld

Storage

Mounting

Swings

down

for Use

MPD 85860

Effective 11/21/07

Out-of-the-way storage

Jack stores out

of the way. Ready for

instant use when needed.

Jack

Tab

Rod

Push

Down

Release

Only

Lever

Drop Leg

Extends

Downward