Aube Technologies 1031A Manuale d'uso

Sfoglia online o scarica il pdf Manuale d'uso per Termostato Aube Technologies 1031A. Aube Technologies 1031A 2. Aube technologies inc. programmable thermostat owner's guide

Stampa la pagina

Your new electronic thermostat is equipped with a microprocessor

with proportional integral adaptive (PIA) temperature control

technology for total comfort.

Clock/Day settings

Heating is On

Setpoint is displayed

Return/Exit

when arrow appears

Power (On/Off)

Program settings

Manual mode

Installation & Wiring

1.1

Guidelines

Turn off power to the heating system at the main power panel to

avoid electrical shock. The installation must be performed by an

electrician.

High voltage thermostats must be installed onto an electrical

box.

For a new installation, choose a location about 1.5 metres above

the floor.

The thermostat must be installed facing the heating system.

The thermostat must be installed on an inside wall.

Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or

concealed chimneys or stove pipes.

1.2

Installation Procedure

Remove the screw holding the control module to the power

base.

NOTE:

Please note that the screw cannot be completely removed.

Lift the control module to remove it from the power base.

On the power base, remove the screw holding the wire cover

and wire the thermostat.

NOTE:

The terminals are designed for wires of cross-section mea-

suring 0.33 to 2.5 mm

Once all wiring is complete, secure wire cover.

Secure the power base onto the electrical box using the

mounting holes.

Mount the control module onto the power base and secure using

the screw.

Return power to the heating system.

NOTE:

Keep the thermostat's air vents clean and free from obstruc-

tions.

TH136

TH136 Programmable

Thermostat

Owner's Guide

Auto mode

Current program

Adjustment buttons

Remote Input Wiring

The TH136 is equipped with a remote input which allows connection of a

telephone controller (optional CT240) or a home automation system.

When a signal is received through this input, the TH136 will automatically

switch from normal operating mode to Frost Protection

versa.

NOTE:

For details on operating the telephone controller, see Operating

Modes.

2.1

Connection to the CT240

Connect CT240 terminals A and C to

TH136 terminals X and C respectively.

You must respect the polarity.

2.2

Connection to a home

automation system

Connect the TH136 to the home

automation system as displayed in the

wiring diagram.

Installing the Batteries

When you first install the batteries, the unit runs a

sequence of tests which lasts approximately 5 seconds.

After the tests, the screen should display the current

temperature.

NOTE:

We recommend replacing the batteries at least

once a year.

The TH136 will display an icon

batteries must be replaced. This icon will be displayed

for 60 days; after this delay, the TH136 will shut down

the heating unit. Once batteries have been replaced,

you will have to reprogram the clock & day settings; all

other programming is stored in a protected memory.

On/Off Button

The thermostat is equipped with an On/Off button

making it possible to put the thermostat in sleep mode

when its use is not required (e.g. summer). This will not

affect the clock or programming.

Clock and Day Settings

Press

; the hour segment flashes.

Press

to set the hour.

Press

; the minutes segment flashes.

Press

to set the minutes.

Press

; the day flashes.

Press

to set the day.

Press

to exit.

Operating Modes

5.1

Automatic

Executes the schedule. Press Auto to activate the

Auto mode.

5.2

Manual

Maintains a constant temperature. Press

activate the Manual mode and set the temperature

using

5.3

Frost Protection

Maintains the Frost Protection setpoint during a

prolonged absence. The Frost Protection setpoint is

pre-programmed to 10°C. To modify, see Advanced

Programming. There are 2 ways to activate the

Frost Protection mode:

From the thermostat:

Press

for 1 second to activate the Manual

mode. Hold

displayed. To deactivate the Frost Protection

mode, activate the Auto or Manual mode.

From a telephone (remote location) when the TH136

is connected to a CT240 telephone controller.

NOTE:

For details on how to activate the Frost Protection mode using a

telephone, refer to the CT240 Instruction Manual.

WARNING:

When the Frost Protection mode is activated remotely, it

must be deactivated remotely.

indicating that the

for 3 seconds. The

icon is

400-136-001-C

2008-02-01

mode, or vice

Automatic

Manual

Frost Protection

1/2