G
TH11 4
User Guide
Non-programmable
Thermostat
Description
Aube's TH114 non-programmable thermostat can be used to control
the ambient air temperature or floor temperature. You can select
among the following temperature control modes:
2.1 Temperature
Display (S1)
The S1 switch is used to select between "C (default) and "F.
2.2 Temperature
Control Mode (S2)
This switch is used to select the temperature control mode.
F.
To select the F mode (default)
AF: To select the A or AF mode
O
Installation
U p o n
tests
ture.
Arrow appears
when the setpoint
is displayed
A mode:
F m o d e :
AF mode:
>
controls and displays the ambient air temperature
>
c o nt r ol s a n d di s pla y s t he fl oor tem perat ur" , ri ng
an external temperature sensor
)
controls and displays the ambient air temperature
>
m a in t ain s th e fl oo r t empe ratu re wit hin des i red
l im it s us in g an ex terna l tem perat ure s ens or
O
Refer to the installation instructions of the power base.
@ Insert the tabs at the top of the control module in the slots at the
top of the power base.
O
Secure the control module using the captive screw underneath
the ba se .
Control module
Air vents
NOTE: Keep the thermosfaf's air vents clean and unobstructed at all
times.
- r L ,
f - E
t - . - l
GFr[x-
I
1$t I
Actual or setpoint
temperature
Unoccupied mode
indicator
Ground fault indicator 2
Temperature
adjustment button
Backlight button
On/Standby switch 3 4
H e a t i n g
i n d i c a t o r 1
€=-
,:,
V
CiE
,0,
-.-l
!==
L
L
-
.
L
L
-
I The thermostat displays the percentage use of heating required to maintain the desired
t e m p e r a t u r e . F o r e x a m p l e , 1 f i s d i s p l a y e d w h e n h e a t i n g i s a t 4 0 p e r c e n t
D i s p l a y
t
f t
l f f
i l t l
f t f t l
% u s e o f h e a t i n g
1 Io 24%
25Io 49%
50 to 74%
75 to 99%
1 0 0 %
' G F I a p p e a r s w h e n t h e g r o u n d f a u l t p r o t e c t i o n h a s t r i g g e r e d .
3 Place the thermostat in Standby to cut power to the heater when it is not in use (e.g. in
s u m m e r ) .
4 To reset the ground fault protection, switch the thermostat to Standby and back to On.
6|
n^-i,^,tf atiOn
9
r . r u r r r r u l
The configuration switches are located at the back of the control
m o d u l e (f a c e pl a te ) .
r
\
!
AF
r
o
.;
Power-up
power-up, the thermostat uncjergoes a series of
before disptaying the actuat (measured) temnera-
| ;f;
I
l
l
$) Error Messages
I L l:l I rne measured temperature is below the thermostat's
dis-
I nrrt I play range. Heating is activated.
I Hl
I ffre measured temperature is above the thermostat's
dis-
|
| play range. Heating is deactivated.
| ,!r
I Verify the thermostat and sensor connections.
rHr4
400- 1 '1 4-0 1 6-4
1 t 3 t 0 7
Stampa la pagina