3onedata TNS5500-4GT-8POE Manuale di installazione rapida - Pagina 3
Sfoglia online o scarica il pdf Manuale di installazione rapida per Interruttore 3onedata TNS5500-4GT-8POE. 3onedata TNS5500-4GT-8POE 4. Managed rack-mounted industrial ethernet switch
Stampa la pagina
RS232, which could be connected to PC for device CLI
command management. The interface adopts RJ45 port. The
pin definitions of RJ45 are as follows:
No.
2
3
Definition
TXD
RXD
【Checking LED Indicator】
This device provides LED indicators for monitoring the work
status of the device, which has simplified the troubleshooting
process comprehensively. The function of each LED is
described in the table as below:
LED
Status
Description
PWR is connected and
ON
running normally
PWR
PWR is disconnected and
OFF
running abnormally.
Power supply, port link
ON
alarm
ALARM
Power supply, port link
OFF
without alarm
The device is powered on
ON
or the device is abnormal.
The device is powered off
RUN
OFF
or the device is abnormal.
Blink 1 time/s, system is
Blinking
running well.
Ethernet port connection is
ON
active.
Link/Act
Blinking
Data transmitted
(X1-X8/G1-G4)
Ethernet port connection is
OFF
inactive.
POE(X1-X8)
ON
POE port is powering other
devices.
POE port is not powering
OFF
other devices.
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device's configuration interface via IE
browser is shown as below:
Step 1
Configure the IP addresses of computer and the
5
device to the same network segment, and the
network between them can be mutually accessed.
GND
Step 2
Enter device's IP address in the address bar of the
computer browser.
Step 3
Enter device's username and password in the login
window as shown below.
Click "OK" button to login to the WEB interface of
Step 4
the device.
Note:
The default IP address of the device is "192.168.1.254".
The default username and password of the device is
"admin".
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
100M M12
10/100Base-T(X), M12 (Female),
4-Pin D-Coded, automatic flow
control, full/half duplex mode,
MDI/MDI-X automatic detection;
Optional PoE output.
Gigabit M12
10/100/1000Base-T(X)，
M12(Female)，8-Pin A-Coded
automatic flow control, full/half
duplex mode, MDI/MDI-X
automatic detection; support
Bypass function
POE
PoE power supply pin：1, 2 are
negative；3, 4 are positive
Console port
CLI command management port,
RJ45
Alarm interface
3-pin
5.08mm
blocks, 1 relay alarm information
output,
capability
10A@125VAC
Indicator
Power indicator, run indicator,
interface
indicator POE indicator (only for
PoE product)
Exchange attributes
Backplane bandwidth
12.8G
Packet buffer size
3Mbit
MAC table size
8K
Power supply
Input power supply
110VAC/DC (100~240VAC/DC)
3-pin
5.08mm
Input terminal
blocks
Consumption
TNS5500-4GT-8T
No-load：14.30W@110VDC
Full-load：14.85W@110VDC
pitch
terminal
the
current
loading
is
5A@30VDC
or
indicator,
alarm
pitch
terminal