CON-TEC Dynamo CTL-335 ES Manuale
Sfoglia online o scarica il pdf Manuale per Accessori per biciclette CON-TEC Dynamo CTL-335 ES. CON-TEC Dynamo CTL-335 ES 2. Led rear light
Stampa la pagina
Manual Dynamo
LED Rear Light
CTL-335 E / CTL-335 ES
Congratulations on the purchase of your new device. The user's manual is part of this device and
contains important information to safety, installation and disposal. Familiarize yourself with all
operating and safety instructions before using the device. Use the device as described and in the
specified areas of application. Keep this manual in a safe place and have it with you when using the
device.
Used symbols
Green Point – Recycling the packaging
Symbol for the detection of electrical and electronic devices
Test mark of the Federal Motor Transport Authority (K with
K XXXX
the following approval number)
Proper use
The product is intended for use on bicycles with pedal assistance and serves the illumination of the
road. This LED front light is approved according to the currently valid RTLR (StVZO). The product is
intended for outdoor use.
Note:
The light should only be installed on bikes with pedal assistance that meets one of the following
conditions. If after unloading-conditioned disconnection of the drive assistance still an uninterrupted
electricity supply of the lighting system is guaranteed for at least two hours or the drive assistance
can be used as an alternator transitional to continue to provide the lighting system with power.
WARNING! LIFE AND ACCIDENT HAZARD FOR INFANTS AND CHILDREN!
Never leave children unattended with the packaging material, because of suffocation danger by
swallowing packaging parts. Always keep the device away from children. The device is not a toy!
This device can be used by children of age 8 and over and by persons with reduced physical or
mental capabilities or lack of experience and knowledge if they have been supervised or instructed
concerning the safe use of the device and by understanding resulting hazards. Children are not
allowed to play with the device. Cleaning and user maintenance should not be carried out by
children without supervision. Do not disassemble the device. Improper repairs can cause
significant risks for the user. Only have repairing made by qualified personnel.
Manual_TL-335 E
Safety information
- Do not look into the LEDs of the front
- Do not point the LED front light directly at people or animals.
- The light beam of the LED front light must point straight in direction.
- The light distribution may be obscured by no other attached parts or pieces of luggage, not even partially.
- The LEDs are not interchangeable. If the LED fails, the entire luminaire must be replaced.
LED rear light and rear reflector
1
2
3
4
5
Mapped components
Rear light
1
2 LEDs rear light
2
Integrated rear reflector
3
Mounting screws
4
Cable connection for dynamo
5
LED rear light assembly
Mount the rear light (1) to the carrier. Use the included screws and nuts.
Connection to the E-bike system
On the back of the rear light (1) is the contact plug (5) for connection to the light system. Plug the non-
insulated line ends to the contacts according to the polarity.
Black cable = power
Black-white cable = earth
Rear light adjustment
Reference axis
90 °
Attention:
Regularly check the correct setting and mounting height of your rear light. The rear light must be
mounted in a range from 250 to 1200 mm above the ground. It must be mounted and adjusted so that
the reference axis is parallel to the vehicle longitudinal mid-plane and parallel to the road surface (see
figure).
Operation
Front
The rear light is switched on and off via the e-bike system. Check regularly for proper function. A setting
or a "programming" is not necessary for the brake indicator function. It is automatically active with the
connection to the dynamo (or headlight). In case of a negative acceleration 2 LEDs of the brake
indicator function are additionally activated for approx. 3 seconds, so that 4 LEDs shine, while the brake
indicator function is active.
Attention: TL-335 E Stop: The brake indicator function is not a brake light.
Back
Reference axis
90 °