3onedata TNS5800 Series Manuale di installazione rapida - Pagina 2
Sfoglia online o scarica il pdf Manuale di installazione rapida per Interruttore 3onedata TNS5800 Series. 3onedata TNS5800 Series 3. Layer 3 rack-mounted industrial ethernet switch
Anche per 3onedata TNS5800 Series: Manuale di installazione rapida (4 pagine), Manuale di installazione rapida (4 pagine), Manuale di installazione rapida (5 pagine), Manuale di installazione rapida (4 pagine)
Stampa la pagina
Step 4
Check and confirm the product is firmly installed on
the rack, then mounting ends.
【Disassembling Device】
Step 1
Device power off.
Step 2
Unscrew the fixed mounting lug screw on the rack.
Step 3
Shift out the device from rack, disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and power
on.
Power OFF operation: First, remove the power plug,
and then remove the wiring section of terminal block.
Please pay attention to the above operation sequence.
【Power Supply Connection】
110VDC power supply
This
provide two independent DC
power supply systems, P1
and
reverse connection protection and power redundancy backup.
Power interface adopts 8-pin 5.08mm pitch terminal blocks
(includes 6-pin power supply), pin definition are shown as
above. Power supply input range: 110VDC (66~156VDC).
【Relay Connection】
This device adopts 8-pin
5.08mm
blocks and supports 1 relay
alarm output, the relay occupies 2 pins, pin definition is shown
as above. R1 and R2 are a group of normally open contacts of
the device alarm relay, which is open in normal no-alarm state
and closed when any alarm information appears. For example,
they are closed when powered off, and send out alarm. The
relay supports the output of DC power supply alarm
information or network abnormality alarm. It can be connected
to alarm light or alarm buzzer or other switching value
collecting devices, which can timely inform operators when
the alarm occurs.
【Console Port Connection】
after connecting to PC. The interface adopts RJ45 port, the
pin definition as follows:
Pin No.
Definition
【Communication Interface Connection】
100M M12 Interface
Model II of the device provides 8 10/100Base-T(X)
interfaces, the interface type is M12 D-Coded 4-Pin
slot (female). The definitions of M12 pin are as
follows:
series
of
devices
Pin No. Definition Description
1
2
P2,
which
support
3
4
Gigabit M12 interface
pitch
terminal
Pin No.
The
series
products
provide
1
debugging port based on RS232 serial port which
can conduct device CLI command management
2
3
5
TXD
RXD
GND
TX+
Positive send data of 100M Ethernet
RX+
Positive receive data of 100M Ethernet
TX-
Negative send data of 100M Ethernet
RX-
Negative receive data of 100M Ethernet
This
Series
device
provides
4
10/100/1000Base-T(X) interfaces, the interface
type is M12 X-Coded 8-Pin slot (female). The
definitions of M12 pin are as follows:
Definition
Description
Pin No.
Definition
1
D0+ (DA+)
2
D0- (DA-)
3
D1+ (DB+)
4
D1- (DB-)
5
D3+ (DD+)
program
6
D3- (DD-)
7
D2- (DC-)
8
D2+ (DC+)
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working status with a comprehensive simplified
troubleshooting; the detailed status of each LED is described
in the table as below:
LED
Indicate Description
ON
P1/P2
OFF
ON
ALM
OFF
or
12
ON
RUN
OFF
Description
Positive bi-directional data of
Gigabit Ethernet group 1
Negative bi-directional data of
Gigabit Ethernet group 1
Positive bi-directional data of
Gigabit Ethernet group 2
Negative bi-directional data of
Gigabit Ethernet group 2
Positive bi-directional data of
Gigabit Ethernet group 4
Negative bi-directional data of
Gigabit Ethernet group 4
Negative bi-directional data of
Gigabit Ethernet group 3
Positive bi-directional data of
Gigabit Ethernet group 3
P1/2 is connected and running
normally
P1/2 is disconnected and
running abnormally
Power supply or port link has
alarm
Power supply or port link has no
alarm
The device is powered on or the
device is abnormal.
The device is powered off or the
device is abnormal.