Anywire B284SB-02-1KPLP30 Manuale - Pagina 8
Sfoglia online o scarica il pdf Manuale per Accessories Anywire B284SB-02-1KPLP30. Anywire B284SB-02-1KPLP30 16.
Stampa la pagina[Transmission Line Connection]
For connection to the transmission line, use the cable included in this unit. Make
sure that connections of the positive and negative polarities are correct.
Transmission line
■Example of fitting the LP connector at the end of transmission line
[When 2-pole LP connector (LP2-PWH-10P) is used]
The LP connector (link connector) is a connector
that integrates male and female terminals.
Both "connection" and "branching" can be made
simply by connecting two connectors of the
same type.
Place the wires in the grooves so that the black wire (DN) is on the hinge
side of the cover, fold A over B and engage the hook C to fasten it.
Bracket insertion hole
Bracket
After pressure-bonding, ensure
that the hooks ③ to ⑥ are
securely engaged.
Master unit
FK2-125-100
LP2-BR-10P
DP, DN
[When 4-pole LP connector (LP4-WW-10P) is used: Example of trunk cable with 2 wires]
Master unit
FK2-125-100
LP4-WR-10P
DP, DN
To LP4-WW-10P,
pressure-bonding
transmission line link
connector
Red: DP (＋)
Black: DN (−)
Finished outer diameter of
core wire
φ1.5
UL style 2103
2-wire × AWG24 (black) φ4.1
Pin No.
1
1
2
2
Cover
B
A
The condition in which
the cover is fitted.
C
Ensure that the hooks
① and ② are engaged.
Pressure-bond using a dedicated tool by
guiding the metal bracket on the
connector body into the hole of the cover.
③ ④
Dedicated tool: LP-TOOL
⑤ ⑥
To LP2-PWH-10P,
pressure-bonding
transmission line link
connector
DP (Red), DN (Black)
ASLINKSENSOR
Pin No.
1
2
3
4
DP (Red), DN (Black)
ASLINKSENSOR
-B284SB0*1K**P30 8/16-
[When 4-pole LP connector (LP4-WW-10P) is used: Example of trunk cable with 4 wires]
Trunk cable LP connector
Pin No.
Description
1
2
3
4
[Various Settings]
Description
DN
Address setting
DP
■Common procedure for address writer operation
Be sure to connect to the AnyWireASLINK master unit to use.
ARW-04 (an address writer) of Rev. (Ver.) 2.01 or later is needed for word
address setting.
ARW-04 of Rev. (Ver.) 1.01 or later will do for parameter settings other than
word addresses.
① ②
For the details of the operating method, refer to the product guide of ARW-04.
1. Connect this unit to the AnyWireASLINK master unit.
A transmission signal is needed to write or read setting parameters.
Set parameters with the address writer with a transmission signal
connected to the transmission line (DP, DN) of the terminal.
Transmission
signal
2. All AnyWireASLINK devices require settings.
Specify settings while pointing the address writer at the setting port of this unit.
(Hold the light emitting/receiving part as close to the setting port as possible.)
Setting port
Description
DN
Address setting
DP
An address number is set as a beginning number from which part of the
Not used
transmission frame is occupied to the unit.
Not used
Set the address number within the range of "0 to 254."
！
CAUTION
The factory-set address is "bit address 255" or "bit address 511," which indicates
that an address has not been set.
The factory-set address varies depending on lot No., as follows:
For S/W version "B" or later version: Bit address 511
For S/W version "A" or 3-digit lot No.: Bit address 255
Input and output operations are disabled with the factory-set address.
Example:
Master unit
FK4-125-100
LP4-WR-10P
DN
DP
0V
24V
24V, 0V, DP, DN
To LP4-WW-10P,
pressure-bonding
transmission line link
connector
Parameter setting
Red: DP
Black: DN
*Use a 24V DC stabilized power supply.
L IN
K
A L
M
IN 0
k P
a
IN 1
Lot No. 19ECBNB
ASLINKSENSOR LP connector
Pin No.
Description
DN
1
DP
2
Not used
3
Not used
4
DP (Red), DN (Black)
ASLINKSENSOR
AnyWireASLINK
master
24V DC*
L IN
K
A L
M
IN 0
k P
a
IN 1
S/W version