3onedata IAP2300R-4A25-2GT-P12 48 Manuale di installazione rapida - Pagina 2

Sfoglia online o scarica il pdf Manuale di installazione rapida per Punto di accesso wireless 3onedata IAP2300R-4A25-2GT-P12 48. 3onedata IAP2300R-4A25-2GT-P12 48 4. Industrial roaming wireless ap

Stampa la pagina

device backboard.

Step 2

Place the device on the wall as reference or

reference installation dimension; mark 4 bolt

positions on the wall.

Step 3

Attach the equipment to the marked wall and

tighten it with M4 screws to the marked position.

Mounting ends.

【Disassembling Device】

Step 1

Device power off.

Step 2

Hold the equipment steady and unscrew the screw

on the wall

Step 3

Take out the device, disassembling ends.

【DIN-Rail Mounting】

The product adopts 35mm standard DIN-Rail mounting which

is suitable for most industrial scenes, mounting steps as

follows:

Step 1

Check whether the DIN-Rail mounting kit that

comes with the device is installed firmly.

Step 2

Insert the bottom of DIN-Rail mounting kit (one side

with spring support) into DIN-Rail, and then insert

the top into DIN-Rail.

Tips:

Insert a little to the bottom, lift upward and then

insert to the top.

Step 3

Check and confirm the product is firmly installed on

DIN-Rail, then mounting ends.

【Disassembling DIN-Rail】

Step 1

Device power off.

Step 2

After lift the device upward slightly, first shift out the

top of DIN-Rail mounting kit, and then shift out the

bottom of DIN-Rail, disassembling ends.

Note before powering on:

Power ON operation: First insert the power supply



terminal block into the device power supply interface,

and then plug the power supply plug contact and power

on.

Power OFF operation: First, remove the power plug,



and then remove the wiring section of terminal block.

Please pay attention to the above operation sequence.

【Power Supply Connection】

DC power supply



The device provides 6-pin 5.08mm

pitch power supply input terminal

blocks, among which power supply

occupies the left 4 pins (the right 2

pins are reserved) Supports P1 and

P2 two independent DC power

supply systems, when one of the power supplies fails, it could

switch to another one immediately to ensure the device power

supply is not interrupted. Power supply supports non-polarity

and anti-reverse connection. Voltage range: 12~48VDC.

48VDC POE power supply input



The WAN port of this device supports POE power receiving.

【DIP Switch Settings】

The device provides 4 pins DIP switch for function

setting, in which "ON" is the enabled end. DIP

switches definition as follows:

DIP

Definition

operation

Restore

Set the switch to ON and power

factory

on the device again, then set it

defaults

back after one minute.

Reboot

The device will restart

immediately after setting the DIP

to ON

Reserved

【Checking LED Indicator】

The device provides LED indicators to monitor the device

working status with a comprehensive simplified

troubleshooting; the function of each LED is described in the

table as below:

LED

Indicate

Description

WIFI is running normally

2.4G/5G

WIFI is running abnormally or

OFF

closed

The device is powered on or the

device is abnormal.

RUN

The device is powered off or the

OFF

device is abnormal.

Blinking

The device is running normally

All indicators are off, which

means the WLAN signal at the

opposite end is weak or no signal

Only one indicator is on, which

means the WLAN signal at the

opposite end is weak

Two indicators are on, which

means the WLAN signal at the

opposite end is normal

Three indicators are on, which

means the WLAN signal at the

opposite end is relatively strong

All indicators are on, which

means the WLAN signal at the