AOG L series Manuale di avvio rapido

Sfoglia online o scarica il pdf Manuale di avvio rapido per griglia AOG L series. AOG L series 2. Stand alone outdoor gas grill
Anche per AOG L series: Manuale di avvio rapido (2 pagine), Manuale di avvio rapido (2 pagine)

Stampa la pagina

"L" Series

CAUTION: For your safety read the installation instructions and owner's manual provided with the grill.

1-Safety

INSTALLER: Leave these instructions with consumer.

This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI

Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).

This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.

This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply

system at pressures up to and including ½ psig.

WHEN INSTALLING THE UNIT FOR USE WITH PROPANE (L.P.) GAS, YOU MUST BE AWARE OF THE ENCLOSURE REQUIREMENTS AND YOU MUST

VENT THE UNIT IN ACCORDANCE TO YOUR OWNER'S MANUAL. FAILURE TO DO SO MAY LEAD TO PROPERTY DAMAGE OR BODILY INJURY,

INCLUDING DEATH.

This grill is designed for outdoor use only. DO NOT use this grill inside a building, garage, or enclosed area (see paragraph below). DO NOT use this grill

in or on a recreational vehicle or boat.

Important:

If installing this grill in a COMBUSTIBLE enclosure, the correct AOG insulating liner must be used. Consult the liner instructions for

counter cut-out dimensions and installation.

A minimum 5 foot clearance is required between the countertop and the overhead construction. When installed under combustible overhead construction, the area

above the cooking surface of the grill must be covered with an exhaust hood. The exhaust hood provides the protection for the combustible overhead construction.

DO NOT use this appliance under unprotected combustible overhead construction.When installed under overhead non-combustible construction, an exhaust

hood is highly recommended. When using an exhaust hood: the area above the cooking surface of the grill must be covered with a hood larger than the cooking

area of the grill, and with a minimum of 1200 CFM (cubic feet per minute) for proper outdoor application.

Installation must be performed by a qualiﬁ ed professional service technician.

2-Unpacking

Carefully unpack the grill, removing all packing material and protective ﬁ lm. Verify that all

parts have arrived undamaged by consulting the parts list in the owner's manual. Remove

foam packed hardware from oven area. (See Fig. 2-1.)

Consult the parts list in the owner's manual. If any parts are missing or damaged, immediately

contact the AOG dealer before beginning installation.

3-Installation

Location

Refer to the INSTALLATION REQUIREMENTS section of your grill owner's manual

for complete details.

CAUTION:

Wind blowing into or across the rear oven lid vent (Fig. 3-1)

can cause poor performance and/or dangerous overheating.

Orient the grill so that the prevailing wind blows toward the

front of the grill (Fig. 3-2).

CAUTION:

To prevent dangerous overheating, the rear of the unit must have a

minimum clearance of 4" from any backsplash/non-combustible wall.

Connect Gas supply

These quick start instructions assume a natural gas or household propane conﬁ gured unit. See main instructions for propane cylinder units.

Note: This section is only an overview of installation to the gas supply. Refer to the grill owner's manual for complete grill installation details.

Route the attached ﬂ ex connector with regulator (located underneath the grill) to the gas-supply stub. (An adapter is required if the gas-supply stub is other

than 1 / 2 " in diameter.) Turn OFF the gas supply at the source. Then connect the regulator to the gas-supply stub. Use pipe joint compound that is resistant

to all gasses on the male pipe ﬁ tting and tighten securely. DO NOT use pipe joint compound to connect ﬂ are ﬁ ttings. See Fig. 3-3.

Turn all burner control knobs to the OFF position. Turn the gas supply on. Then carefully check all gas connections for leaks with a brush and half-soap/half-

water solution before lighting. NEVER USE A MATCH OR OPEN FLAME TO TEST FOR LEAKS.

The control panel must be ﬂ ush with the enclosure face as shown in Fig. 3-4.

Proper grill airﬂ ow must be maintained as shown in Fig. 3-5. Do not block. It is not necessary to remove the control panel or knobs for installation.

6" Grill clearance

Fig. 3-3

Flex connector

REV 0 - 1611140830

CONSUMER: Retain for future reference.

Gas

Adapter

supply

Shut-off valve

Regulator

(required, not

included, must be

installed within 6

feet of the unit)

Built-in Outdoor

Gas Grill

Quick Start Guide

INCORRECT

Rear oven lid vent

YOU MUST PROTECT REAR OVEN

VENT FROM PREVAILING WIND

Fig. 3-1

Countertop

Overhang

Control panel

must be ﬂ ush with

enclosure face

Fig. 3-4

Remove plastic

zip-ties

Lift out foam packed hardware

Fig. 2-1

C C O O R R R R E E C C T T

CORRECT

PLACE GRILL SO PREVAILING WIND

BLOWS TOWARD FRONT OF GRILL

Fig. 3-2

Maintain proper ventilation

airﬂ ow

Fig. 3-5

L-C2-481