Dunavox DAVS-72.185 Manuale di istruzioni - Pagina 6
Sfoglia online o scarica il pdf Manuale di istruzioni per Raffreddatore per vino Dunavox DAVS-72.185. Dunavox DAVS-72.185 16.
Stampa la pagina
- 1. Important Safeguards
- 2. For Your Safety
- 3. Product Features
- 4. Installation of Your Appliance
- 5. Before Using Your Appliance
- 6. Reversing the Door Hinge
- 7. Operating Your Appliance
- 8. Use and Control - Single Zone
- 9. Use and Control - Dual Zone
- 10. Temperature Display
- 11. Temperature Memory Function
- 12. Door Alarm
- 13. Care and Maintenance
- 14. Warranty
○
2.
Install the handle
○
two screws
and flat washers
,3
3.
Replace the door gasket.
Note: All parts removed must be saved to
do the reinstallation of door.
REVERSING THE DOOR HINGE
It is possible to reverse the door on this appliance, if
required.
To do so, follow the steps below:
DESIGN 1 – For built-under models
1.
Remove the bottom hinge (1) by unscrewing the
four lock screws (2). Be careful to hold the glass
door firmly after removing the screws. (Fig. 1)
2.
Gently pull down to remove the glass door from the
right top hinge and place it on a padded surface to
avoid the risk of damage. Then remove the right top
hinge (5). (Fig. 3)
3.
Unscrew and transfer hinge pin (3) and/or door
stopper (4) of the bottom hinge to the opposite side.
(Fig. 2)
4.
Pop out the cover caps on the left side of cabinet
and use them to
cover the screw holes on the right
hand side.
5.
Screw the alternative left top hinge (7), included in
the fittings,
on the left hand side of cabinet. (Fig. 3)
6.
Unscrew and transfer the holes cover (8) and lock
catch (9) to the opposite side of glass door. (Only
for models with lock on the ventilation grille) (Fig. 4)
Rotate the door 180° (No need for models with lock
7.
on the door) and relocate the door to the designated
position. Then screw the bottom hinge assembly on
the left designated position and tighten it after the
door is leveled.
tightly as shown above with
,4
○
provided.
,2
8.
Transfer the handle & plugs to the opposite
positions if need.
DESIGN 2 – For fully integrated models
1.
Remove the glass door by unscrewing the eight lock
○
○
screws
and
,3
firmly after removing the screws and place it on a
padded surface to avoid the risk of damage.
2.
Unscrew and transfer the door supporter
opposite side.
Rotate the glass door 180°and refit the glass door to
3.
the opposite side. Then screw and tighten it after
the door is leveled.
DESIGN 3 – For tall models
1. Remove the bottom hinge
four lock screws
firmly after removing the screws.(Fig. 1)
2. Gently pull down to remove the glass door from the
right top hinge and place it on a padded surface to
avoid the risk of damage. Then remove the right top
○
hinge
,9. (Fig. 4)
3. Pop out the cover caps on the left side of cabinet and
use them to
cover the screw holes on the right hand
side.
4. Screw the alternative left top hinge
the fittings,
on the left hand side of cabinet. (Fig. 4)
6
. Be careful to hold the glass door
,4
○
○
,1 by unscrewing the
○
,2. Be careful to hold the door
○
,8. included in
,2 to the