Casio 1570 Manuale d'uso - Pagina 6
Sfoglia online o scarica il pdf Manuale d'uso per Guarda Casio 1570. Casio 1570 11.
Stampa la pagina
Using Auto Memory Measurement
1. Confirm that the auto memory measurement
Auto memory measurement
indicator is shown on the display. If it is not,
indicator
use the procedures under "Selecting Auto or
Manual Memory Measurement" to select
A
B
auto memory measurement.
A L M
A LT I
S I G
RECALL
2. Hold down D until the watch emits a short
A-LIGHT
AUTO
AUTO
A L
MANUAL
beep, indicating the start of the measure-
m
˚C
ment.
P
• The data measured when you first start auto
C
D
memory measurement is also stored into
memory.
• The auto memory measurement indicator flashes on the display when you
start auto memory measurements. The indicator continues to flash
(indicating that measurements continue) even if you change modes.
• Auto memory measurement cuts off automatically whenever there are 49
sets of data stored in memory. The 50th set of data measured when you
stop the measurement operation in step 3 below is also stored in memory.
3. To stop measurements at any point, hold down D again until the watch
emits a short beep.
• A final measurement is taken when you switch auto memory measurement
off, and that data is also stored into memory. Such data is indicated by
FIN
during the recall operation.
Using Manual Memory Measurement
1. Confirm
Manual memory
measurement indicator is shown on the
measurement indicator
display. If it is not, use the procedures
under "Selecting Auto or Manual Memory
B
A
Measurement" to select manual memory
A L M
A LT I
S I G
RECALL
measurement.
A-LIGHT
AUTO
MANUAL
A L
MANUAL
2. Hold down D until the watch emits a short
m
˚C
beep, indicating that a measurement is
P
taken.
C
D
3. Repeat step 2 whenever you want to take a
reading.
• Button operation becomes impossible during the 4 or 5 seconds that it
takes to complete a measurement. Normal operation will return once the
operation is finished.
Setting a Reference Altitude
After you set a reference altitude, the watch automatically calculates the
difference between the current altitude and your preset value. The altitude
measurements produced by this watch are subject to error caused by changes
in air pressure. Because of this, we recommend that you set the reference
altitude during your climb whenever one is available.
1. In the Altimeter Mode, hold down A until
B
A
the display clears. After 4 or 5 seconds,
A L M
A LT I
S I G
RECALL
either
A-LIGHT
AUTO
A L
MANUAL
value (if set) will start to flash. The data
m
flashes because it is selected .
• The
C
D
setting is being used for the calibration.
2. Press D to increase the current reference altitude value by 5 m or B to
decrease it. Holding down either button changes the value at high speed.
• If you have selected feet as your unit of measurement, the above
operations change the reading in increments of 20 feet.
• You can set the reference altitude within the range of –6000 m to 6000 m
(–19680 feet to 19680 feet).
• Pressing B and D at the same time returns to the
3. After setting the reference altitude you want, press A to return to the
Altimeter Mode.
About the Altitude Alarm
The altitude alarm sounds for about five seconds whenever the current
altitude matches a preset value. You can press any button to stop the alarm
after it starts to sound. Note that the altitude alarm sounds only while the
watch is in the Altimeter Mode.
Example:
If you set the altitude alarm at 130 meters, it will sound when you pass the
130-meter mark on your way up and on your way back down.
To set the altitude alarm
1. In the Altimeter Mode, hold down A until the display clears. After 4 or 5
seconds, either
OFF
or the current reference altitude value (if set) will start
to flash. The data flashes because it is selected .
2. Press C to change the selection in the following sequence.
Reference Altitude Setting
Altitude Alarm Setting
that
the
manual
memory
OFF
or the current reference altitude
OFF
indicator appears when the factory
OFF
message.
Memory Measurement Setting
3. Press C to select the altitude alarm setting
Altitude alarm on indicator
display (indicated by the
A
B
4. Press D to increase the altitude alarm
value by 5 m or B to decrease it. Holding
A L M
A LT I
S I G
RECALL
A-LIGHT
AUTO
A L
MANUAL
down either button changes the value at
m
high speed.
• If you have selected feet as your unit of
measurement, the above operations change
C
D
the setting in increments of 20 feet.
• You can set the altitude alarm setting within the range of –6000 m to 6000
m (–19680 feet to 19680 feet).
• Setting an altitude value automatically switches the altitude alarm on.
5. After setting the altitude alarm value, press A to return to the Altimeter
Mode.
To switch the altitude alarm off
1. In the Altimeter Mode, hold down A until the display clears. After 4 or 5
seconds, either
OFF
or the current reference altitude value (if set) will start
to flash. The data flashes because it is selected .
2. Press C to change the selection in the following sequence.
Reference Altitude Setting
Altitude Alarm Setting
3. Press C to select the altitude alarm setting display (indicated by the
ALM
indicator).
4. Press D and B at the same time to change the setting to
switch the altitude alarm off.
5. After switching the altitude alarm off, press A to return to the Altimeter
Mode.
About the Target Altitude Graph
The Target Altitude Graph appears in the
Graphic area
graphic area of the display in the Altimeter
A
B
Mode. It divides the difference between your
start point
A L M
A LT I
S I G
RECALL
A-LIGHT
AUTO
A L
MANUAL
the altitude alarm into 10 equal parts. It then
m
shows a graph that shows your current
˚C
location, to give you some idea of how much
P
farther you must go to reach your altitude
C
D
setting.
*
The start point differs according to what type of memory measurement
procedure you are using. With auto memory measurements (AUTO
shown on the display), the start point is the first altitude measured. With
manual memory measurements (MANUAL
start point is 0 m (0 ft).
• The target altitude graph is not shown on the display if the altitude alarm is
off.
Example:
• The display below would appear at a current altitude of 160 m when you are
using manual memory measurement with a target altitude setting of 200 m.
Eight points on the graph are darkened because you are 8/10 of the way to
your target.
• The display below would appear at a current altitude of 160 m when you are
using auto memory measurement with a target altitude setting of 200 m and
a starting point of 100 m. Six points on the graph are darkened because you
are 6/10 of the way to your target.
1570-6
ALM
indicator).
Memory Measurement Setting
OFF
and
*
altitude and the value you set for
shown on the display), the
This indicator "
"
appears once you pass the
target altitude.