Casio 2412 Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Guarda Casio 2412. Casio 2412 7.

Stampa la pagina

Camera Rest Interval

Camera Mode operations consume considerable battery power. To protect

against premature rundown of the battery power, the watch automatically goes

into a rest interval, during which you will be unable to re-enter the Camera

Mode after you exit it. The length of the rest interval is equal to the amount of

time you spent in the Camera Mode before you exited it. This means that if you

exit the Camera Mode after being in it for 20 seconds, you will be unable to re-

enter the Camera Mode for about 20 seconds.

Remaining rest interval time

If you try to enter the Camera Mode during a rest

interval, the message WAIT appears on the display,

along with a countdown of the remaining rest interval

time.

WAIT 13

• The maximum rest interval is 60 seconds. The

CHECKING

maximum rest interval may be as long as 70

VOLTAGE

seconds following recording of an image using the

camera timer .

Displayed Image Size and Memory Image Size

Though the size of images displayed by this watch is 78 × 72 dots (78 × 80

dots in the case of an image that includes the recording date and time), the

size of the image stored in memory is 176 × 144 dots. This means that after

you transfer images to your computer or another device, you can display them

with 176 × 144 dots.

Alarm, and Hourly Time Signal Sounds

The watch does not emit any alarm, or Hourly Time Signal sound while it is in

the Camera Mode.

Controlling the Camera Mode Image

You can use the following procedures to adjust the brightness, to specify the

type of lighting present when recording an image, and to configure the camera

timer.

Adjusting Image Brightness

The watch automatically sets the brightness of the image when you record it.

You can also change the brightness level manually when you want to

compensate for backlighting of the subject, very dark backgrounds, etc.

To adjust image brightness

1. Before recording an image in the Camera Mode,

press A twice to enter the brightness setting

screen.

2. Use E (brighter) and B (darker) to adjust the

brightness of the image. A larger brightness value

indicates a brighter setting, while a smaller value

indicates a darker setting.

• You can set brightness to one of 15 levels in the

‰

range of –7 to +7. The initial default level is ±0.

• It may take some time after you press B or E

before the change in brightness is reflected on

the displayed image.

• A brightness setting you make remains in effect

Brightness value

until you change it or exit the Camera Mode.

Automatic brightness adjustment is the initial

default whenever you enter the Camera Mode or

change the lighting type setting.

Important!

Even with manual brightness adjustment, you may not be able to obtain an

acceptable image when recording images under very bright or very dark

lighting conditions.

Specifying the Lighting Type

The type of lighting present when recording, greatly affects the resulting image.

You can use the procedure below to set up the watch for shooting indoors or

outdoors, which helps to ensure proper brightness for recorded images.

To specify the lighting type

Before recording the image in the Camera Mode, press E or B.

Use E or B to cycle through available lighting type settings in the sequence

shown below.

OUTDOOR

Press E.

Lighting

type

OUTDOOR

Press B.

• You can select OUTDOOR for outdoor lighting, INDOOR for indoor lighting, or

DUSK for shooting at twilight or under other conditions where lighting is dim.

• The lighting type setting you make remains in effect until you change it or exit

the Camera Mode. OUTDOOR is the initial default whenever you enter the

Camera Mode.

• The screen refresh rate is relatively slow when DUSK is selected, which can

make changes in the image on the display appear slow.

USER'S GUIDE 2412

INDOOR

DUSK

INDOOR

DUSK

Using the Camera Timer to Record Images

You can select two seconds, five seconds, or 10 seconds as the camera timer

start time.

To record an image using the camera timer

1. In the Camera Mode, press A to display the

Camera timer indicator

camera timer screen.

2. Use E and B to change the camera timer setting

in the sequence shown below.

• The default setting is 2 seconds.

TMR 4

Seconds

Camera timer time

3. Press F to start the camera timer and perform a record operation when the

end of the countdown is reached.

• The number of seconds remaining is counted down on the display.

• Pressing F while a countdown is in progress records the image and

cancels the remainder of the countdown.

• To stop a camera timer countdown and reset the timer start time to its

initial value, press A, B, or E.

• Pressing D while a camera timer countdown operation is in progress

changes to the VISUAL DATABANK Mode.

• The watch automatically exits the Camera Mode after about one

minute. If one minute elapses while camera timer operation is in

progress, the timer operation continues until it is complete. The watch

automatically returns to the VISUAL DATABANK Mode after recording

the image.

VISUAL DATABANK

Besides viewing images, you can use the VISUAL DATABANK Mode to delete

images, to attach text to images, etc.

Important!

The alarm and Hourly Time Signal do not sound while the VISUAL DATABANK

Mode setting screen is on the display.

To view recorded images

1. In the Timekeeping Mode or the Camera Mode, press D to enter the

VISUAL DATABANK Mode .

• A screen showing the number of images in memory appears for about

one second, followed by a four-image thumbnail screen. The last image

you were viewing or the last image you recorded has a boundary

around it on the thumbnail screen.

Current Time

After about

PLAY 1 ‰ : 5 8

one second

Number of images in memory

2. Use B and E to move the boundary between

images until the one you want is selected.

• Holding down either button moves the boundary

at high speed.

3. Press C to display the enlarged version of the

selected image with recording date and time.

PAGE ‰ ‰ 3

• It can take from one to four seconds for the

enlarged version of the selected image to appear

clearly on the display.

• While the enlarged version of an image is on the

display, you can use B and E to scroll to

another image, if you want.

4. While the enlarged version of the selected image is

Selected image

on the display, press C to display any text

(with boundary)

assigned to the image (if there is any).

Text

• Each press of C cycles through display settings

in the sequence shown below.

TARO

Recording time

2‰‰1. 6.29.P 3:25

and date

Press

Selected image

Image with text

Press

Seconds

Thumbnail screen

PAGE ‰ ‰ 4

Image number

Thumbnail screen