Casio 2581 Manuale d'uso
Sfoglia online o scarica il pdf Manuale d'uso per Guarda Casio 2581. Casio 2581 2. Radio controlled watch
Anche per Casio 2581: Manuale d'uso (2 pagine)
USER'S GUIDE 2581/2671
MA0302-A
How a Radio-controlled Watch Works
What is a radio-controlled watch?
Your radio-controlled watch is designed to receive a time
calibration signal that contains standard time data and adjust its
current time setting accordingly
.
Signal received using
built-in antenna.
Transmitter
Long-wave time
calibration signal
Watch decodes
received data
and converts it
Signal data
to time data.
Decoding
Time is
Time data
adjusted
Cesium
according to
Inside the watch
Watch
atomic clock
time data.
After the watch receives the Standard
T i me signal, it
performs internal calculations to determine the current time.
Because of this, there may be an error of up to one second
in the displayed time.
Location
Reception is dif
ficult and may even be impossible in the locations
described below
. A void such locations when performing signal
reception.
You should think of your watch operating like a radio or
TV when it
is receiving the calibration signal.
Among or near buildings
Near high-voltage lines
Next to a household
Inside a vehicle
appliance or office equipment
(automobile, train, plane, etc.)
(TV, speaker, fax, PC, etc.)
In a location where there is
Near mountains
radio interference
(construction site, airport, etc.)
If you are experiencing problems with reception, move away from
the types of locations described above to a location with better
reception, and try again.
Calibration Signal
The Japanese calibration signal (Call Sign: JJY) is maintained by
the independent Japan Ministry of Posts and
T elecommunications
Communication Research Laboratory (CRL). It is a long wave
signal transmitted 24 hours a day from the Mt. Otakadoya
transmitter (40kHz) located in
T amura-gun, Fukushima Prefecture,
and from the Mt. Hagane transmitter (60kHz) located on the
border between Saga Prefecture and Fukuoka Prefecture.
The U.S. calibration signal (Call Sign: WWVB) is transmitted by
the National Institute of Standards and technology from Fort
Collins, Colorado.
Though the calibration signal is normally transmitted 24 hours
a day
, transmission may be interrupted occasionally due to
maintenance, lightening, etc.
Receiving the Calibration Signal
There are two methods you can use to receive the time calibration
signal.
Auto reception (Reception is performed automatically at 2:00,
4:00, and 6:00 each morning.)
Manual reception (Y
ou initiate reception using a button
operation.)
The watch is set up for auto reception at the factory
, so all you
need to do is to place it in a location that allows good reception
each night.
Setting Up to Make Reception Easier
Remove the watch from your wrist and place it somewhere so its top
(12 o'clock side, where the antenna is located) is facing
approximately in the direction of the signal transmitter
. Keep the
watch away from metal objects.
Resin band
Metal band
Orienting the watch so it is sideways to the transmitter makes it
more dif
ficult to receive the signal.
Do not move the watch while it is receiving the calibration signal.
The following explanation covers the radio-controlled timekeeping function only.
For other functions, go to the download page for Module 2578,
which is the export model that has the same functions, except for radio-controlled timekeeping.
Reception Range
This watch is designed to receive the standard time calibration signal of Japan (JJY) or of the United States (WWVB).
The signa
received depends on the current Home City setting.
When this Home City is selected:
Transmitter Locations
500km
500km
Mt. Hagane
(60kHz)
1000km
Under optimum conditions, the calibration signal should be
receivable up to 1,000 kilometers from the transmitter
. Note
that the wave is relatively weak at distances greater than
500km, so reception may be poor at long distances.
Geographic contours, nearby buildings, the season, and the time of day can make reception impossible even when you are within range of
the transmitter.
Best reception is possible late at night.
Time Required for Reception
Signal reception takes anywhere from about two to six minutes.
Note that when "A/T" (auto) is specified as the transmitter
selection mode, signal reception can take up to 12 minutes.
* See "Specifying the Transmitter Selection Mode in Japan" for
more information.
Triggering Reception Manually
In the
T i mekeeping Mode:
Hold down the B B B B B button for
about two seconds.
The watch beeps and reception
starts. Ongoing reception is
indicated by the
icon and the
receive indicator
. See "Receive Icon
and Indicator" for more information.
To interrupt reception
Press the B B B B B button.
All other buttons besides B are disabled during signal reception.
When reception is successful
The watch adjusts its current time setting, and then beeps and
displays the time and date of the adjustment.
The
icon and the receive indicator remain on the display to
indicate that reception was successful.
When reception fails
The watch does not adjust its current time setting, and displays
"ERR" instead.
The display also return to the normal timekeeping screen
automatically if you do not perform any operation for about one
or two minutes.
You can receive this signal
Either the Mt. Otakadoya signal (40kHz) or the Mt. Hagane signal (60kHz)
Fort Collins, Colorado signal
1000km
Transmitter Location
1000km
Mt. Otakadoya
(40kHz)
Fort Collins
Under optimum conditions, the calibration signal should be
receivable up to 3,000 kilometers from the transmitter. Note
that the wave is relatively weak at distances greater than
1,000km, so reception may be poor at long distances.
Receive Icon and Indicator
While reception is in progress, the
icon and the receive indicator
cycle from "Unstable" through
"Stable" as shown below. How far
they cycle depends on the signal
strength. Keep the watch in a
location where reception is stable
while reception is in progress.
Unstable
Even under optimum reception conditions, it takes at least
10 seconds before reception starts.
Use the receive icon and receive indicator to check
reception status and to determine the best location for
signal reception.
Note that weather, the time of day, surroundings, and other
factors can all affect reception.
l that is
3000km
Receive indicator
Receive icon
Stable
1