Casio 2687 Manuale operativo

Sfoglia online o scarica il pdf Manuale operativo per Guarda Casio 2687. Casio 2687 5.

Stampa la pagina

MO0306-EA

Operation Guide 2607 2637 2687

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to carefully read this manual and keep it on hand for later reference

when necessary.

Expose the watch to bright light to charge its battery before using it.

You can use this watch even as its battery is being charged by exposure to bright

light.

• • • • • Be sure to read "Battery" of this manual for important information you

need to know when exposing the watch to bright light.

If the display of the watch is blank...

Sleep indicator

General Guide

• Press C to change from mode to mode.

• In any mode, press L to illuminate the display.

Timekeeping Mode

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

• The watch is equipped with a Time Recorder feature that lets you record the current

Home City time (month, day, hour, minutes, seconds, and DST on/off setting) with

the touch of a button. See "To record a Time Recorder time" for more information.

• Pressing D displays the Last Signal screen (date and time that the time calibration

signal was last received) in the Timekeeping Mode.

Day of week

indicator

Month – Day

Hour : Minutes Seconds

Current Time Setting

This watch automatically adjusts its time setting in accordance with a time calibration

signal. You can also perform a manual procedure to set the time and date, when

necessary.

• Before using the watch in Western Europe, first use the procedure under "Setting Up

the Watch for Use in Western Europe" to set the time in accordance with a time

calibration signal.

• Note that after you set your Home City (the city where you normally use the watch)

code, you must also turn on the watch's time calibration signal receiver if you want to

enable auto time calibration. See "About Auto Receive" for more information.

• See "Setting the Time and Date Manually" for information about manual settings.

Setting Up the Watch for Use in Western Europe

You need to make the following three settings before using this watch in Western

Europe. The following provides a general overview of the setting procedure. For full

details, see "Setting the Time and Date Manually" and "Time Calibration Signal

Reception".

• Specify the city code for your Home City (the city where you will normally use the

watch).

• Select the auto Daylight Saving Time (summer time) setting.

• Perform the manual time calibration signal receive operation to set the current time.

To set up the watch for use in Western Europe

City code

Receiving indicator

If the sleep indicator (S /SLEEP ) is on the display, it

means that the display is blank because the watch's

Power Saving function has shut it to conserve power.

Power Saving automatically turns off the display and

enters a sleep state whenever your watch is left in an area

where it is dark for a certain period.

• The initial factory default setting is Power Saving on.

• The watch recovers from the sleep state if you move it to

a well-lit area

, if you press any button, or if you angle

the watch towards your face for reading.

It can take up to two seconds for the display to turn on.

• See "Power Saving Function" for more information.

World Time Mode

Press C.

Receive time

Press D.

Receive date

Last Signal Screen

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Use D(+) and B(–) to select the city code you want to

use as your Home City.

• The following are the city codes for major cities in the

Western Europe time zones.

BER and PAR: Berlin, Paris, Milan, Rome,

Amsterdam, Hamburg,

Frankfurt, Vienna

LON: London

3. Press C and the Daylight Saving Time (summer time)

setting screen appears.

4. Use D to select AUTO (auto DST).

• Auto DST specifies auto switching between Daylight

Saving Time (DST) and Standard Time.

5. Press A twice to exit the setting screen.

6. Hold down D for about two seconds until the watch

beeps.

• Release D and the message RC! appears to indicate

that signal reception has started.

• Time calibration signal reception takes from two to six

minutes. Take care that you do not move the watch

during this time.

About This Manual

• The operational procedures for Modules 2607, 2637 and 2687 are identical. All of

the illustrations in this manual show Module 2607.

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the "Reference" section.

(Light)

Module 2637

Module 2607

Time Recorder Mode

Stopwatch Mode

• When getting ready to receive the time calibration signal, position the watch as

shown in the nearby illustration, and place it near a window in a location where there

are no nearby metal objects.

Metal Band

Resin Band

• The watch should not be on its side or facing the wrong way.

• See the information under "Time Calibration Signal Reception Precautions" if you

experience problems with time calibration signal reception.

• After signal reception is complete, the display of the watch changes to the Last

Signal screen.

Time Calibration Signal Reception

This watch is designed to pick up a time calibration signal and update its time setting

in accordance with the signal. There are two different methods you can use to receive

the signal: Auto Receive and Manual Receive. With Auto Receive, the watch

automatically receives the calibration signal four times each day and makes

appropriate adjustments. With Manual Receive, you perform a specific button

operation to receive the calibration signal.

• This watch is able to receive the time calibration signal

transmitted from Mainflingen, Germany (located 25

kilometers southeast of Frankfurt). Signal reception is

possible within the area represented by a circle with a

radius of about 1000 kilometers.

• At distances further than about 500 kilometers, the

signal may become weak and reception may be

impossible under certain conditions.

• Signal reception may be poor in the shaded area on the

map, even though it is within 1,000 kilometers of the

signal transmitter.

Frankfurt

Note

• If you are using the time calibration signal to set the time for this watch, be sure to

correctly set your Home City. Otherwise, there is the chance that the watch will not

set the correct time. See "Setting the Time and Date Manually" for details.

• Note that signal reception is possible only when the watch is within range of a time

calibration signal transmitter, and BER, PAR, LON, or ATH is selected as the Home

City code.

• See "City Code Table" for a complete list of available city codes.

• The current time setting in accordance with the time calibration signal takes priority

over any time settings you make.

• Auto receive is turned on when the watch is shipped from the factory.

• See the information under "Time Calibration Signal Reception Precautions" if you

experience problems with time calibration signal reception.

(Light)

Module 2687

Alarm Mode