DUNLOP CRYBABY Rack Wah Manuale

Sfoglia online o scarica il pdf Manuale per Pedale musicale DUNLOP CRYBABY Rack Wah. DUNLOP CRYBABY Rack Wah 2.

Stampa la pagina

DIRECTIONS

Getting Started:

To begin using your DCR-2SR Cry Baby Rack Wah, run a cable from your guitar

to the Wah Input jack on the Rack Wah's back panel. Then connect a cable from

the Wah Output jack to the input of your amplifier. Connect a DCR-1FC Foot

Controller to Control Pedal Input 1 on the DCR-2SR's back panel with the

included stereo cable. Note: The stereo cable between the Foot Controller and

the Rack Wah does not pass signal. This helps maintain sonic integrity by

reducing the amount of cable and connections between your guitar and amp.

Turn the DCR-2SR on and then turn on your amp. With the Wah button on the

front panel depressed (green On LED illuminated), step on the controller pedal to

activate the toe switch. Rock the pedal back and forth to hear the Wah effect.

Selecting a Wah Tone

The DCR-2SR has an absolutely huge range of Wah tones. To begin the quest for

your ultimate Wah sound, set the Range knob to 1.2kHz (the lowest or bassiest

frequency range) and, for starters, set the Q knob to 12:00. Play a riff as you rock

the Wah pedal. A good way to hear exactly what the various settings sound like

is to simply play a series of hammer-ons and pull-offs—like a trill between two

notes—and gradually turn the Q knob as you rock the pedal. The Q control

changes the breadth of the Wah effect, from narrow and sharp to broad and

subtle. Rotating this knob will give you a good idea of what the 1.2kHz setting

can do. Next, switch the Range knob to 1.4kHz and go through the same process,

and then 1.6kHz, 1.8kHz, and so on. With a little experimentation, you'll find a

particular Range and Q setting that best suits your individual style.

Fine Tuning Your Wah Tone

Now that you've chosen the frequency range (with the Range knob) and breadth

of your Wah tone (with the Q knob), you can fine-tune it further with the

DCR-2SR's 6-band EQ. To do this, depress the EQ button on the front panel. Start

with all six knobs at 12:00 and then gradually turn each knob clockwise (to boost

the selected frequency) and counterclockwise (to cut or attenuate the selected

frequency). The possibilities are truly endless, so begin with subtle adjustments.

Boosting Your Wah Tone

Once your Wah sound is dialed in, you can easily determine where that tone sits in

the mix with the Boost control. This knob presets a gain boost of up to 10dB that kicks

in when you engage the Wah effect. This control performs a couple of different

functions. With a cleaner setting on your amp, it will provide a substantial volume

boost, bringing your Wah lines to the front of the mix. With a dirty tone, the Boost

function creates more distortion, saturation, and sustain. It can create endless,

sustaining feedback on virtually any note with a loud amplifier, perfect for lead work.

Using the Optional Volume Pedal

The Crybaby DCR-2SR comes equipped with an additional loop for remote volume

control. This is preferable to merely running a volume pedal between your guitar and

amp because the *pedal that controls the DCR-2SR volume function is only a voltage

controller. It does not pass signal, therefore there is no need to run any additional

cable between your guitar and the Crybaby Rack Wah. **To use the volume function

of your DCR-2SR, plug your guitar into the DCR-2SR Volume Input jack. Run a short

patch cable from the Volume Output jack to the Wah Input jack. Run a cable from the

Wah Output jack to your amp. Next, plug a DCR-1FC Controller into one of the Wah

Control Pedal input jacks via a stereo cable. Then plug a Volume Control *Pedal into

the Volume Control Pedal jack via a mono cable. To activate the volume function,

depress the Volume button on the front panel.

* The Crybaby GCB-80 Volume Pedal (with 250k pot) or an equivalent pedal can be used as the DCR-2SR

Volume Control Pedal by connecting a standard 1/4" mono cable from its output jack to the DCR-2SR

Volume Control Pedal jack.

** The loop for remote volume control can be inserted anywhere within the signal chain, including FX

loops. Only one example is described here for simplicity. DO NOT connect to amplifier speaker outputs.

DUNLOP MANUFACTURING, INC. P.O. BOX 846 BENICIA, CA 94510 U.S.A.

TEL: 1-707-745-2722 FAX: 1-707-745-2658 WWW.JIMDUNLOP.COM

C U S T O M S H O P

DCR-2SR Rack Wah Manual

Congratulations on your purchase of your new

Rack Wah! Dunlop is committed to producing state-of-the-art products

with the same bullet-proof construction and spectacular tone that

made us famous. Please take a minute to read through this manual so

you can get the most out of your Rack Wah.

FEATURES

• Amazingly flexible wah tones

• Legendary Fasel inductor for incredibly vocal wah tone and sweep

• Rack mounting keeps signal chain in the rack

• Six selectable frequency range

• Variable Q control

• Six controller inputs to accommodate multiple pedals on stage

volume pedal capabilities

• Six-band EQ for additional tone sculpting

• Preset volume boost up to 10dB

DCR-2SR

Cry Baby