Free The Tone ARC-4 Manuale d'uso - Pagina 12

Sfoglia online o scarica il pdf Manuale d'uso per Apparecchiature di registrazione Free The Tone ARC-4. Free The Tone ARC-4 16. Audio routing controller
Anche per Free The Tone ARC-4: Procedure di aggiornamento del firmware (18 pagine)

Stampa la pagina

Selecting Mute Circuit to be Activated when MUTE Switch is Turned On (MT-PT): ON/OFF switch 6

MT-PT

MUTE-A

ENTER

PARAMETER

 Turn the PARAMETER encoder to select the desired mute circuit.

 Turn the PARAMETER encoder to select the desired mute circuit operation.

Parameter 1: MUTE-A, MUTE-B, MUTE-C

Parameter 2: ON, OFF

Default: MUTE-A (ON), MUTE-B (ON), MUTE-C (OFF)

Selecting Control Terminal to be Activated Simultaneously when MUTE Switch is Pressed (MT-LK): ON/OFF switch 7

MT-LK

CTL1

ENTER

PARAMETER

 Turn the PARAMETER encoder to select the desired control terminal.

 Turn the PARAMETER encoder to select the desired operation.

Parameter 1: CTL1 to CTL4

Parameter 2: ON, OFF (default = OFF)

Setting Operation when Same PS/L Switch is Pressed (SC-PS): ON/OFF switch 8

SC-PS

ENTER

 Turn the PARAMETER encoder to select the desired operation.

Parameter 1: OFF, PS10, NONE (default = OFF)

PS10: When the same preset switch is pressed twice, PS10 is recalled at the second press. If all of the LOOP settings of PS10 are set to OFF, a preset in which

all LOOPs are bypassed will be recalled.

NONE: Even if the same preset switch is pressed multiple times, the preset is not recalled and no MIDI signal is sent after the second and following presses.

This setting is required if the device reloads the MIDI signal and does not output the effect sound when the same preset switch is pressed twice and the

MIDI signal is sent again.

OFF: The unit is set to the default status. By pressing the same preset switch, the preset is recalled and the defined MIDI signal is output.

UTILITY: PS7/L7 switch

Internal detailed settings of the ARC-4 are done in these cofiguration modes.

Locking Out Setting Changes from Front Panel (AT-LC): ON/OFF switch 1

AT-LC

ENTER

 Turn the PARAMETER encoder to select ON or OFF.

Parameter: ON, OFF (defalut = OFF)

NOTE

The initial setting is OFF. If set to ON, the Lock function is automatically activated after about 10 minutes of no user operation and it becomes impossible to change settings from the

front panel.

 ON

MUTE1

ENTER

PARAMETER

ENTER

 OFF

CTL1

ENTER

PARAMETER

ENTER

SC-PS

AUTO

PARAMETER

ENTER

OFF

AT-LC

PARAMETER

ENTER

Protecting Memory Contents from Change (MM-PR): ON/OFF switch 2

MR-PR

ENTER

 Turn the PARAMETER encoder to select ON or OFF.

N.B. The initial setting is OFF. If set to ON, it becomes impossible to edit the stored contents. When set to ON, the M.PROTECT dot in the Display-1 illuminates.

Parameter: OFF, ON (default = OFF)

Adjusting LED Brightness (LD-BR): ON/OFF switch 3

LD-BR

ENTER

 Turn the PARAMETER encoder to adjust the LED brightness.

Parameter: MID (middle), HIGH (bright), LOW (dim) (default = MID)

NOTE

The initial setting is MID. Set to HIGH if the LEDs are dim and not clearly visible in open-air performances, etc.

Setting Expression Pedal's Calibration (EP-CB): ON/OFF switch 4

EP-CB

HIGH

ENTER

EX.PEDAL

The expression pedal connected to the EXT terminal is calibrated in this configuration mode. By execituting this process, you can control from the minimum to

maximum values precisely. Be sure to use an expression pedal with variable resistance from 10kΩ to 25kΩ.

 When the display shows "HI GH," put the expression pedal to the toe down position to get the maximum value. Then press the ENTER switch to confirm.

 When the display shows "LOW," put the expression pedal to the toe up position to get the minimum value. Then press the ENTER switch to confirm.

 When the display shows "DONE," then the calibration is completed.

NOTE

If "ERROR" is shown after pressing the ENTER switch, please check the expression pedal and/or the connecting cable.

Receiving ARC-4's Data (DP-LD): ON/OFF switch 5

DP-LD

RECV

ENTER

PARAMETER

ENTER

 Turn the PARAMETER encoder to select "RECV."

 When "YES" is shown, press the ENTER switch to put the ARC-4 in data receive ready status "– – –."

 The display starts counting up when data reception starts.

Parameter 1: RECIEVE [RECV], SEND

NOTE

This ARC-4 units automatically receives data when another ARC-4 starts data transmission. When it is completed, the dispaly shows "DONE" then returns to "DP-LD."

OFF

MR-PR

PARAMETER

ENTER

MID

LD-BR

PARAMETER

ENTER

 LOW

DONE

ENTER

EX.PEDAL

ENTER

– – –

YES

ENTER

DONE