Free The Tone MOTION LOOP Manuale di avvio rapido - Pagina 2
Sfoglia online o scarica il pdf Manuale di avvio rapido per Pedale musicale Free The Tone MOTION LOOP. Free The Tone MOTION LOOP 2. Pitch shiftable short looper
Stampa la pagina
Factory Presets
The MOTION LOOP is shipped with factory presets. They are stored
in the user preset memory after No. 128 with the [F:] preset number
prefix. Users can turn the PARAMETER encoder to select and recall
the desired factory preset.
Note that this factory preset area is protected against recall, write,
or delete operation via MIDI signals.
Note that the parameters of the factory presets have already been
copied into the user preset area to be used after being edited to the
user's preference.
For more details about the factory presets, please refer to the
product page on our website.
Recalling Presets
128 presets provided by the MOTION LOOP can be recalled in
various ways.
Use PRESET Footswitch to Switch between
Presets 1 and 2
Press the PRESET footswitch to switch the presets.
NOTE
Each time the PRESET footswitch is pressed, Presets 1 and 2 are
switched instantly. It is useful to store frequently used presets in
Preset 1 and Preset 2 and switch them.
Recall Desired Preset from 128 Presets
1. Press the HOME switch until the screen shows a preset number
and preset name.
2. Turn the PARAMETER encoder until the desired preset number is
shown in the display. The two red LEDs above the PRESET
footswitch flash alternately. At this time the preset is not recalled.
3. Press the PRESET footswitch to recall the desired preset. When
the preset is recalled, the two red LEDs above the footswitch stop
alternate flashing.
Recall Preset by MIDI Signal
The MOTION LOOP's presets are switched by receiving a program
change number MIDI signal from an external MIDI device. The MIDI
channel of the device that sends the program change number has to
be the same as the MIDI channel of the MOTION LOOP.
Initialization
The following steps clears all presets and returns them to the
factory status.
1. Hold the ▶ cursor key down and turn on the power to the unit.
2. Release ▶ cursor key when the display shows "INITIALIZING."
3. This completes the initialization.
Edit Menu
The effects unit's parameters in each preset and the function of
each knob, PARAMETER encoder, or footswitch, etc. are changed in
Edit mode.
How to Confirm Parameter Changes or Settings
1. Press the HOME switch to show the HOME or Assignment Display
screen.
2. Press the ▶ cursor key to show the HOME screen.
3. Turn the PARAMETER encoder to show the desired setting menu.
4. Press the ◀/▶ cursor key to select the desired setting.
5. Turn the PARAMETER encoder to change the parameter.
FUNCTION
HOME SCREEN
ASSIGNMENT
SCREEN
OCTAVE UP/DOWN
①PITCH SETTING
1, 2OCT UP
1, 2 OCT DOWN
LOOP LEVEL
②LOOP SETTING
-100〜100
FADE CURVE
③WAVEFORM SETTING
SHALLOW, DEEP, A CURVE,
C CURVE, REVERSE
DELAY SUBDIVISION
④DELAY SETTING
OFF, 1, 1/2, 1/4, .1/8, 1/8
DRY SETUP
⑤DRY & FOOTSW SETTING
ON, AUTO, OFF
⑥KNOB & EXP ASSIGN
KNOB-L ASSIGN
⑦PRESET NAME
PRESET NAME
Global Settings
Setting Procedures for Global Functions
In the Global Settings screen, settings related to the entire operation
such as MIDI receive channel selection, calibration of expression
pedal, etc. are configured.
1.Hold down the HOME switch for about 2 seconds to show the
Global Settings screen.
2.Use the ◀/▶ cursor key to show the desired setting screen.
3.Configure the desired function.
4.Press the HOME switch. The display changes to the HOME screen.
6. When confirmation or editing is completed, press the HOME
switch. The display shows the HOME screen again.
How to Change Parameters and Saving Them
in Preset
1. Press the SAVE switch. The SAVE LED and preset number display
start flashing.
2. Turn the PARAMETER encoder to change the preset number
shown in the display to the desired preset number. (Skip this step if
overwriting in the same preset number.)
3. Press the SAVE switch. The edited parameter is stored in the preset.
Pressing the 【HOME】 switch to show the desired setting screen
/
【◀】
【▶】
Pressing the
cursor Key to show the desired setting screen
Turn the 【PARAMETER】 encoder to show the desired setting menu
PITCH VALUE
PITCH SPEED
PITCH SHIFT
000〜100
000〜100
REPEAT, SINGLE
RESET LEVEL
RETRIGGER SETTING
RETRIGGER SENS
RETRIGG, NONE
OFF, FOOTSW, ATTACK
FILTER MODE
FILTER RANGE
SOFT CLIPPING
MANUAL, ENV,
NARROW, WIDE
SYNC BPM, SYNC SPD
DELAY FEEDBACK
DELAY MIX LEVEL
DELAY TRAIL
000〜100
000〜100
ON/OFF FOOTSW
LATCH, UNLATCH
KNOB-C ASSIGN
KNOB-R ASSIGN
ENCODER ASSIGN
Hold down the 【HOME】 switch for about 2 secons to show the Global Setting screen
HOME SCREEN
【◀】
USe the
①
②
Setting of MIDI
Calibration of
Receive Channel
Expression Pedal
(MIDI CH)
(EXP CALB)
NOTE
To cancel the save operation, press the HOME switch (i.e., other than
the SAVE switch) or ◀/▶ cursor key when the number shown in the
display is flashing. Or move the LOOP RATE, E.LEVEL, or FILTER knob
to cancel the save operation. If a parameter of a saved preset has
been changed, a dot appears at the lower right corner of the first
digit of the PRESET number. This dot is turned off when the changed
parameter is saved in the preset.
SLOW DOWN
ON, OFF
RETRIGGER FADE
BPM SETTING
O〜100
OFF, ON
SYNC, OFF, 030〜600
000〜100
OFF, ON
EXP/FS ASSIGN
/
【▶】
cursor key to show the desired setting screen
③
④
Display of
Setting for
【PARAMETER】 Encorder
Expression Pedal
(EXP DISP)
(ENCODER)
LOOP RATE MODE
MANUAL, ENV, RANDOM
⑤
Setting for
【PRESET】 Switch
(PS FSW)