Free The Tone TA-1H Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Pedale musicale Free The Tone TA-1H. Free The Tone TA-1H 6. Multi-dimensional chorus
Anche per Free The Tone TA-1H: Procedure di aggiornamento del firmware (11 pagine)

Stampa la pagina

CONTROLS AND INDICATORS: FRONT PANEL

⑤

⑥

⑪

⑩

①

① Effect ON/OFF Footswitch

Turns on/off the chorus effect. When on,

the LED above the switch illuminates.

② Select Footswitch

•In Preset Mode:

Switches presets 1–4 cyclically, i.e.,

Preset 1 → Preset 2 → Preset 3 → Preset 4

•In Edit Mode (EDIT LED illuminating):

Selects the preset number to save the

current chorus sound settings. The LED

for the selected preset number flashes.

•In Manual Mode: Selects the preset to

be recalled when the unit is switched to

Preset mode.

③ MODE Switch

Switches between Manual and Preset

modes.

④ EDIT Switch

Puts the unit in Edit mode.

•In Preset Mode: Used to modify the

contents of the preset currently recalled.

Press the EDIT switch. Then the LED

above it illuminates and the current preset

number's LED flashes. Now you can

m o d i f y t h e c u r re n t s e t t i n g s . W h e n

completed, select the target preset

⑦

⑧

⑨

③

④

②

number and hold the EDIT switch for

about 1.5 seconds. Your modified settings

are stored in the selected preset memory.

•In Manual Mode: Used to save the

current knob settings to a preset. Press

the EDIT switch. Then the LED above it

i l l u m i n a t e s a n d t h e c u r re n t p re s e t

number's LED flashes. Select the target

preset number and hold the EDIT switch

for about 1.5 seconds. The current

settings are stored in the selected preset

memory.

⑤ DEPTH LEFT Knob

Adjusts the pitch vibration depth of the

LEFT signal. The signal appears at the

OUT-L (MONO) terminal.

⑥ DEPTH CENTER Knob

Adjusts the pitch vibration depth of the

CENTER signal. This signal appears at

both the L and R outputs. In monaural

operation, the signal appears at the

OUT-L (MONO) terminal.

⑦ DEPTH RIGHT Knob

Adjusts the pitch vibration depth of the

RIGHT signal. The signal appears at the

OUT-R terminal. In monaural operation,

the signal appears at the OUT-L (MONO)

terminal.

⑧ HI-CUT Knob

Adjusts the effect sound's timber. Turning

the knob counterclockwise cuts the high

frequencies.

⑨ RATE Knob

Adjusts the speed of pitch vibration.

Turning the knob clockwise increases the

vibration speed.

⑩ LEVEL Knob

Adjusts the volume when the effect is

turned on.

CONTROLS AND INDICATORS: REAR PANEL

⑫

⑬

⑭

⑫ IN Terminal

I n p u t t e r m i n a l o f t h e T R I AVATA R .

Connect your guitar or effects unit, etc. to

this jack.

⑬ OUT-L (MONO) Terminal

•When in stereo operation: Outputs the

s i g n a l s e t b y t h e D E P T H L E F T a n d

DEPTH CENTER knobs.

•When in monaural operation: Outputs

t h e s i g n a l s e t b y t h e D E P T H L E F T,

DEPTH CENTER, and DEPTH RIGHT

knobs.

⑭ OUT-R Terminal

Outputs the signal set by the DEPTH

RIGHT and DEPTH CENTER knobs.

⑮ EXP Terminal

RATE (modulation speed) or HI-CUT

can be controlled in real-time from an

expression pedal connected to this

⑪ DRY MIX Knob

Adjusts the mix balance between the

effect and direct (dry) sounds when the

effect is turned on. When the knob is

turned fully counterclockwise, the output

is the effect sound only. By turning the

knob clockwise, the direct (dry) sound is

mixed to the effect sound.

⑮

⑯

⑰

jack. Use an expression pedal with

variable resistance 10kΩ–50kΩ (our

re c o m m e n d a t i o n : B O S S F L - 5 0 0 L ,

EV-5).

⑯ MIDI IN Terminal

Receives MIDI signals from an external

MIDI device.

⑰ POWER DC9V IN Terminal

Connect the supplied AC adapter to this

t e r m i n a l . A n y A C a d a p t e r t h a t h a s

regulated 9 VDC output, center minus

polarity, and more than 140 mA power

supply capability can be used. A standard

5.5 x ø2.1 mm plug is acceptable.