Free The Tone LDP-1 Manuale d'uso - Pagina 4

Sfoglia online o scarica il pdf Manuale d'uso per Monitor Free The Tone LDP-1. Free The Tone LDP-1 4. 12-digit led display

Stampa la pagina

Copying Presets

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

COPY.

3. Press the PARAMETER encoder.

4. Use the PARAMETER encoder and press the RIGHT/LEFT switch to

select the MSB-LSB-Program Change Number to be the copy

source.

5. Press the UP/DOWN switch to select the second line.

6. Use the PARAMETER encoder and press the RIGHT/LEFT switch to

select the MSB-LSB-Program Change Number to be the copy

destination.

7. Press the PARAMETER encoder.

8. When the Display-2 shows DONE, the operation is completed.

Parameter 1: 000-000-001 to 127-127-128

Parameter 2: 000-000-001 to 127-127-128

MIDI / System Settings

Setting MIDI Receive Channel

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

MIDI/SYSTEM.

3. Press the PARAMETER encoder.

4. Press the UP/DOWN switch to select RX MIDI CH.

5. Turn the PARAMETER encoder to select the desired channel.

Parameter: 01 to 16, ALL (default)

Setting Operation when Same MIDI Program Change Number

is Received Again

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

MIDI/SYSTEM.

3. Press the PARAMETER encoder.

4. Press the UP/DOWN switch to select IGNOR SAME M.

5. Turn the PARAMETER encoder to select ON or OFF.

Parameter: ON, OFF (default)

NOTE

If set to OFF, the same program change number will be shown again when it

is received. If set to ON, that MIDI signal will be ignored.

Setting Display Method

You can set the sequential order and duration of displaying bank/preset

titles. This setting is globally applied to Internal Memory mode.

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

DISPLAY.

3. Press the PARAMETER to confirm.

The subsequent steps are the same as those described in ARC-4

mode (➔ See p.4).

Setting LED Brightness

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

MIDI/SYSTEM.

3. Press the PARAMETER encoder.

4. Press the UP/DOWN switch to select LED BRIGHTNESS.

5. Turn the PARAMETER encoder.

Parameter: 1 (default), 2

NOTE

When 1 (default) is selected, LEDs illuminate at the standard brightness.

LEDs are dimmed if 2 is selected.

Sending LDP-1's Data

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

DATA DUMP.

3. Press the PARAMETER encoder.

4. The Display-1 shows MIDI SEND.

5. Press the PARAMETER encoder to start data transmission.

6. The progress of data transmission can be confirmed with the count

up timer.

NOTE

Before executing the above steps, connect the LDP-1's MIDI OUT/THRU

terminal to the MIDI IN terminal on the destination device with a MIDI cable.

Receiving LDP-1's Data

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

DATA LOAD.

3. Press the PARAMETER encoder.

4. The Display-1 shows MIDI RECEIVE.

5. Press the PARAMETER encoder to make the unit be ready for data

reception.

6. The progress of data transmission can be confirmed with the count

up timer.

NOTE

Before executing the above steps, connect the MIDI OUT/THRU terminal on the

source device to the LDP-1's MIDI IN terminal with a MIDI cable.

Resetting to Factory Default Settings

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

INITIALIZE.

3. Press the PARAMETER.

4. When the Display-1 shows INITIALIZE, press the PARAMETER

encoder.

5. When the Display-1 flashes YES, press the PARAMETER encoder.

6. When the menu display returns after counting up, the reset

operation is completed. All of the stored data will be lost.

Main Specifications / Ratings

• Number of presets: In ARC-4 mode = 2000 presets (10 presets x 200 banks), In Internal Memory mode = 500 presets

• Power supply: Dedicated AC-DC adapter

• Consumption current: approx. 220 mA (9-VDC operation)

• Dimensions: 240 (W) x 54 (D) x 45.5 (H) mm (incl. protrusions such as knobs, etc.)

• Weight: approx. 380 g

• Accessories: Warranty card, Owner's manual, Dedicated AC-DC adapter

• Optional accessory: KS-LD-1 Bracket for LDP-1

Updating Firmware via MIDI

1. Press the MENU switch.

2. Turn the PARAMETER encoder or press the UP/DOWN switch to select

FIRMWARE UPDATE.

3. Press the PARAMETER encoder.

The LDP-1 can update its firmware via MIDI. For the latest firmware

or connection and setup procedures, please confirm with the

product or support page of the Free The Tone website.

Specifications and appearance subject to change without notice.