Dupline Carpark GP 7380 0080 Manuale di avvio rapido - Pagina 4
Sfoglia online o scarica il pdf Manuale di avvio rapido per Apparecchiature di prova Dupline Carpark GP 7380 0080. Dupline Carpark GP 7380 0080 5. Configuration and test unit
Stampa la paginaGP73800080
Mode of Operation (cont.)
experience for the driver.
Offset spaces in Master mode
Fig. 18
When the settings are finished and
ready to transfer to the unit, the Con-
figurator will respond with "Send data
to unit".
Send data to unit (Both sensor and
Master/Slave unit)
Fig. 19
If the transmission of some reason
fails, the Configurator will respond with
"Send failed Try again".
The user must then find out what has
caused the failed transmission before
trying again. Please check cable or
battery in Configurator as possible
problems.
Message from the Configurator
Fig. 20
GTU mode:
When connecting to the Dupline
through the Jack plug, GTU mode is
enabled. This is done by pressing the
"Read / On" button on the Configura-
®
tor when the Dupline
bus is connect-
ed. Then the display will show the
standard GTU "Mode 1".
GTU mode 1
Fig. 21
4
The GTU have 4 modes.
- Mode 1 - Able to see one
Dupline
®
group
- Mode 2 - Able to two Dupline
groups. * See note
- Latch - Able to latch any of the
128 Dupline
- Calibration - Able to send the
calibrate sequence on any of
the 128 Dupline
To change mode:
1. Press « Mode/Enter »
2. Shift between mode options by
pressing either « ← » Or « → ».
3. Select mode by pressing « Mode/
Enter ».
*
How to select the extra group in
mode 2
1. Select mode 2
2. Select the Dupline
by pressing the specific tactile key
a. Example: We want "D" as
the second Dupline
b. Press tactile key "2" one
time and the letter "D" will
appear as second group
Mode 2 selected
Fig. 22
Mode 2 Extra group added
®
bus
Fig. 23
Digital 1 group
Once connected to the Dupline
display shows the status of channel
group A. Active channels are indicated
by their numbers. Pressing «1», «2» ...
«8» will activate the corresponding
®
Dupline
channel in the selected chan-
nel group.
Pressing « ← » or « → » changes the
channel group showing the display.
Digital 2 groups
When the mode "Digital 2 groups" is
selected, the user may select an addi-
Specifications are subject to change without notice (12.12.2008)
Dupline®
tional channel group for permanent
monitoring on the bottom line of the
display. The channel status of the two
®
selected groups can now be moni-
tored, but changing the channel status
through the keys «1» ... «8» only
affects the channels displayed in the
®
channels
upper row of the display. Even so,
pressing the « ← » or « → » key only
changes the channel group in the
®
channels
upper row of the display.
Edit Tx-latch
In this mode it is possible to "latch"
the activation of one or more channels.
This means that the GTU will continue
transmitting on the channel(s) even
though the corresponding transmis-
sion button is released.
To cancel the transmission on a chan-
nel, press the corresponding transmis-
sion button again.
®
letter (A-P)
The latched transmission will continue
even if the channel group or mode is
changed. In order to change the status
®
group.
of a latched transmission, it is neces-
sary to re-enter the "Edit Tx-latch"
mode.
All the latched channels are reset to
normal Dupline
the GTU becomes disconnected from
the Dupline
Sensor Calibration
The Sensor Calibration function is car-
ried out as a sequence of steps. The
function controls one channel on the
Dupline
Select calibration mode.
1. Enter this function and select the
decided Dupline
"SELECT SENSOR CALI GROUP: X"
(X = Group number).
Press « Mode/Enter » when the want-
ed group is selected.
®
, the
Select calibration group
Fig. 24
2. When Group is selected the channel
within the group must be selected.
"SELECT SENSOR CALI CHANNEL:
XY"
®
is a registered trademark. A product of the CARLO GAVAZZI Group
Du line
Fieldbus
Installationbus
®
operation whenever
®
.
®
bus.
®
group:
®