DANLERS EZ CESR Note sull'installazione

Sfoglia online o scarica il pdf Note sull'installazione per Interruttore DANLERS EZ CESR. DANLERS EZ CESR 2. Easyzapp ceiling flush mounted switches

Stampa la pagina

Variants

DANLERS design and manufacture other EasyZAPP Ceiling Flush Mounted

variants, coded by the following order codes:

EZ CESR 10VDC

Suitable for 1-10VDC ballasts

EZ CESR DALI

Suitable for DALI ballasts.

Troubleshooting

The load will not switch on:

• The LUX setting as specified by the EasyZAPP App is set too low and is inhibiting

the switch.

• The moving body is not emitting more IR than the background.

(Person wearing insulating clothing in a warm environment)

• Person is too far from the PIR switch, see detection diagram.

• Person is moving unusually slowly (perhaps when testing).

• The control unit battery is not engaged (ON).

Switch RED dip switch next to the telejack connector on the EZ CESR

control unit towards the centre of the control (see diagram D).

The load switches on when nobody is present:

• Heater causing infra-red variations in a small cold room.

Resite the EZ CESR control away from heater.

• Please contact DANLERS for further technical support.

Precautions and Warranty

This product conforms to BS EN 60669-2-1, BS EN 55015 and BS EN 60730.

Please ensure the most recent edition of the appropriate local wiring regulations are observed

and suitable protection is provided (protected with the appropriate MCB) 1kV over voltage.

Please ensure that this device is disconnected from the supply if an insulation test is made.

This product is covered by a warranty which extends to 5 years from the date of manufacture.

Products available from DANLERS

• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers

• Photocells • Radio remote controls • Time lag switches • Outdoor security switches

• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products

Please call for more information or a free catalogue, or visit our website.

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388

E-mail: [email protected]

Web: www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

15/09/16

EasyZAPP Ceiling flush mounted switches

EZ CESR

EasyZAPP ControlZAPP ceiling surface passive infra-red occupancy switches can

be mounted directly onto solid ceilings or onto a range of different mounting boxes

(diagram A). EasyZAPP devices incorporate a passive infra-red quad sensor to detect

movement of a warm body within their detection zone (diagram B) and a photocell to

monitor the ambient light level.

Please Note: ALL adjustments are made via a freely downloadable EasyZAPP

App available from the DANLERS website. EasyZAPP products cannot be

configured by DANLERS ControlZAPP or ScheduleZAPP apps.

Upon detecting movement, if the ambient light is dark enough, the EasyZAPP device

will turn the load ON. The ambient threshold can be set to between approximately

30 lux to 1000 lux and infinite lux (photocell inactive) via the 'Brightness' settings on

the EasyZAPP App. If no more movement is detected within a pre-selected time as

determined by the EasyZAPP App, then the EasyZAPP device will turn the load off.

This 'Timeout' or time lag can be set via the EasyZAPP App adjuster between 10sec

and 23hrs 59min 59sec.

EZ CESR is suitable for mains switching or DALI switching only.

EZ CESR can switch up to:

• 10 amps (3000W) of resistive loads

• 6 amps (1500W) fluorescent lamps, high frequency or switch start,

incandescent or mains halogen lamps (recommended with integral safety fuse)

• 3 amps (750W) of electronic or wire wound transformers.

• 2 amps (500W) of low energy lamps: CFL, LED, 2D etc.

• 1 amp (250W) of fans or most metal halide lamps.

Start-up mode and Default settings

When the EZ CESR is powered up, it will take 1 minute for the circuitry to stabilise

(detection LED flashing) and ensure the output is off, the EasyZAPP device will then

enter its Default Operating Mode.

Please Note: When in the Default Operating Mode the EZ CESR is set up as

an occupancy switch with a 20 minute turn OFF timeout (time lag) and photocell

disabled.

INS311 EZ CESR

Installation notes