Acer Altos G530 Series Manuale d'uso rapido

Sfoglia online o scarica il pdf Manuale d'uso rapido per Telefono cellulare Acer Altos G530 Series. Acer Altos G530 Series 1. Acer altos g530 server: quick start

Stampa la pagina

Acer Altos G530

Quick Start User's Guide

Thank you for buying an Acer Server Platform.

The following information will help you assemble

your Acer Server Platform and install components.

This guide and other supporting documents are located on the web at

http://global.acer.com/support/index.htm

If you are not familiar with ESD (Electrostatic Discharge) procedures

used during system integration, please see the Acer Altos G530 User's Guide,

available at http://global.acer.com/support/index.htm

Installing the DIMM memory

Notes and Cautions:

1. You must install the correct DIMMs to avoid possible

damage to the mainboard's DIMM sockets. The

mainboard requires DDR2-400 registered compliant

DIMMs.

2. When a single DIMM is used, it must be installed in

the socket labeled DIMM 1B.

3. Population order: 1B, 1A, 2B, and 2A

4. Memory in DIMM 2B and 2A must be populated in pairs.

5. The DIMM size, speed and manufacturer must be the

same within a bank.

6. Memory sizing and configuration is guaranteed only for

qualified DIMMs approved by Acer.

Making connections to the mainboard

Quick reference

Required connections

A: Main power connector

C: Auxiliary signal connector

E: +12V CPU power connector

I: Front panel connector

J: Chassis intrusion connector

K: IDE connector

L: FDD connector

M: Hot-plug backplane connector

O: SATA A1 and A2 connectors

CPU/System fan connections

B: System fan 1 connector

D: System fan 2 connector

F: CPU 1 fan connector

G: CPU 2 fan connector

P/N: PR.R1702.001

Color: Pantone 329 CV + CMYK

Size: 22" x 17" or ( 558.8mm x 431.8mm )

DDR2 DIMM memory identification

The table below lists the supported memory installation

based on memory interleave configuration.

The illustration below shows the correct alignment

between the DIMM notch and the mainboard DIMM

Dank 1

Dank 2

Momory

socket. DDR and DDR2 DIMM notches align differently.

Before installing your DIMMs, make sure the notch

DIMM 1B DIMM 1A DIMM 2B DIMM 2A

Interleave

in the DIMMs align correctly with your mainboard.

512 MB

1-Way

1 GB

1-Way

2 GB

1-Way

512 MB

1-Way

1 GB

1-Way

2 GB

1-Way

512 MB

1-Way

1 GB

1-Way

2 GB

1-Way

Finishing up

Before installing the operating system, you must make I/O connections

and plug in AC power.

1. Connect your keyboard, mouse, video and other I/O cables as shown.

2. Connect the AC power cable.

Removing the left-side panel

1. Remove the two screws

To avoid integration difficulties and

located on the rear edge

possible mainboard damage,

of the left-side panel.

your system must meet the following

2. Press the left-side

minimum requirements:

panel release button.

3. Slide the left-side panel

Processor: One Intel Xeon 2.8 GHz

toward the rear before

processor with 800 MHz FSB.

detaching it from

the chassis.

Memory: Minimum of one 512 MB,

DDR2 400 MHz unbuffered, 240-pin

gold SDRAM DIMM.

Installing the processor

B. Install the processor

Notes and Cautions:

1. When unpacking a processor, hold by the edges

only to avoid touching the pins.

2. The Altos G530 mainboard has a "zero-insertion force"

1. Orient the processor with

socket. If the processor does not drop easily into socket,

the socket so that the proc

make sure lever is in the full-open position.

essor cut out matches the

3. When installing an additional processor, make sure it

socket notch.

has the same stepping and running values at the same

2. Install the processor as shown.

frequency specifications as the default processor.

A. Open the socket retainer lever

Pull the socket retainer

C. Close the socket retainer lever

lever to a fully open,

upright position.

Press the socket retainer

lever down to lock

processor in place.

Installing the four-bay

HDD cage

The Altos G530 accepts the following HDD cages:

- Hot-plug SATA/SCSI HDD cages

- Easy-swap SATA/SCS HDD cages

The main difference between a hot-plug and easy-swap

HDD cage is the presence of a backplane board on the

rear side of the hot-plug HDD cage.

To install the DIMM:

To install the HDD cage:

Open both clips on the socket.

1. Slide the cage into the chassis until it locks into place

Align then insert the DIMM into

with an audible click.

the socket.

2. Attach the power and SATA/SCSI cables to the HDD.

Press the holding clips inward to

lock the DIMM into place.

Check that socket levers are

securely attached.

Mainboard component layout

1: USB ports

17: Clear CMOS, Clear password and

2: Top: PS/2 mouse port

Recovery boot jumper

Bottom: PS/2 keyboard port

18: Primary IDE connector

3: Serial A port

19: FDD connector

4: VGA/monitor port

20: SCSI channel connector

5: Gigabit LAN 1 port (RJ-45)

21: SATA connectors

Gigabit LAN 2 port (RJ-45)

22: Hot-plug backplane connector

6: System fan 1 connector

23: Front panel LED connector

7: Auxillary power supply signal connector

24: I C connector (reserved for ARMC/2)

8: System fan 2 connector

25: CMOS Battery

9: Power supply connector

26: USB 3 and 4 connector

10: DIMM 1B to 1A sockets

27: Chassis intrusion connector

11: DIMM 2B to 2A sockets

28: Serial B connector

12: CPU power supply connector

29: SCSI LED connector

13: CPU 1 socket

30: PCI-X slots (64-bit/66 MHz)

14: CPU 2 socket

31: PCI slots (32-bit/33 MHz)

15: CPU 1 fan connector

32: PCI-Express slot (with x4 throughput)

16: CPU 2 fan connector

Removing the front bezel

1. Locate the system keys (if necessary) and unlock

the system lock on the bezel door.

2. With your finger, slightly bend the plastic retention tabs

to release the latches (1).

3. Gently pull and detach the bezel from the chassis (2).

Installing the heat sink-fan assembly

1. Align the HSF assembly to the processor.

2. Using the screwdriver, tighten the heat sink's four

screws to secure it to the mainboard.

3. Connect the CPU fan cable to its

mainboard connector.

Note: The fan should face the DIMM module's direction.

Installing a hard disk

A. Install a hard disk on the carrier

Install a hard disk on the hard disk carrier (1),

then secure it with the four screws

that came with the carrier (2).

B. Install the hard disk carrier

1. Insert the hard disk carrier into the

cage with the lever still extended.

2. Make sure that the drive is properly

inserted before closing the lever,

then push the lever back until it

clicks into place.