Daspi Eurokit Epo Manuale di istruzioni - Pagina 7

Sfoglia online o scarica il pdf Manuale di istruzioni per Apriporta Daspi Eurokit Epo. Daspi Eurokit Epo 13. Swing gates operator

Stampa la pagina

InstallatIon

To operate a good installation of the gear motor EPO

follow these instructions:

Make sure that the leaves of the gate are perfectly

horizontal.

Install temporary the supports "S1" and "S2" on the

operator.

Install the support "S1" using the pivot "P1" , making

attention to the mounting way (11 mm toward

the high, 13 toward the low,

supplied screws and self-Lubrificate bushes

Install the support "S2" loosing the screw "V" and

introduce the pivot "P" in its base "F" and fix the

security screw "V"

(fig.

Start the operator and move the pivot "P" axle up

700 mm from the back axle of the pivot "P1"

3).

Decide the maximum opening of the leaf, from 90°

to 120°, and consult the table

Decide the vertical position you want to install the

operator.

Make sure that the operator is perfectly horizontal

and weld temporary the support "S1" to the column

of the gate, in the position as per table in fig. 3, and

the support "S2" to the leaf.

If the column is not in iron material, weld the support

"S1" on the support "S3" , and fix it on the column by

special unsupplied screws

Release the gear motors like explained in the par.

"Emergency or manual manoeuvre" , and carry out

a manual opening and closing to check the correct

position of the gear motor.

Dismantle the gear motor from the supports "S1"

and "S2" .

Fix definitively the supports "S1" and "S2" by a very

good welding.

Install the gear motor on the supports repeating the

above instructions.

Make the circuitry like in the control panel manual

and install the obligatory safety devices.

Teach the people intended for the use of the

automation about the controls, safety devices,

emergency manoeuvre and dangerousness deriving

from the utilize of the automation.

Compile the technical booklet and fulfil the eventual

obligations deriving from the regulations in force.

ePo/oPen VersIon

Version with water proof electrical limit switch's

opening/closing, already installed and connected by

DASPI.

Install under the back pivot "P1" the pivot supporting

the cams "PC" , fixing it by supplied screw "V1"

5). Insert the limit switch cams "CM1.CM2" on the

pivot "PC" .

Adjust the cam "CM1" (up) carring out with a

manual manoeuvre the leaf in the maximum wished

opening position, turn the cam till to hear the click

of the limit switch.

fig.

1), and using the

(fig.

2).

(fig.

3).

(Fig.

4).

(fig.

4).

Adjust the cam "CM2" (down) carring out with a

manual manoeuvre the leaf in closing position and

turn the cam till to hear the click of the limit switch.

Carry out an automatic manoeuvre to check the

correct position of the cams "CM1-CM2" and correct

if is necessary.

Fix the screws "V2" to block the cams.

ePo/FIn-MeCC VersIon

1).

Version with mechanical limit switch supplied

installed on the endless screw by DASPI.

Loose the grubs "G1-G2" screwed on stops "FM1-

FM2"

(fig.

6).

(fig.

Put with a manual manoeuvre the leaf in closing

position and turn the stop "FM1" till it touch the

female screw "C" , so fix the grub "G1" .

Put with a manual manoeuvre the leaf in the

maximum wished opening position and turn the

stop "FM2" till it touch the female screw "C" , so fix

the grub "G1" .

Carry out an automatic manoeuvre to check the

correct position of the stops "FM1-FM2" and correct

if is necessary.

We garantize the correct functioning of EPO/OPEN

and EPO/FIN-MECC versions only and exclusively if

provided by DASPI and only if combined with the

original control panel.

eMergenCy or Manual ManoeuVre

You have to do the emergency or manual manoeuvre

or during the installation, or only if the automation

does not work properly or if there is not power

supply.

CuT OFF THE POWEr SuPPLy.

Open the plug on the handle "LS" cover and insert

the supplied key "CH"

Turn the key "CH" clockwise and putting the handle

in vertical position opens the gate manually.

In order to re-establish the normal functioning of

the automation, you have to put again the handle

"LS" in horizontal position and turn the key "CH"

anticlockwise, so take away the key and reinstall the

plug on the handle.

Place the key "CH" in a safety place known

exclusively from the people intended for the use of

(fig.

the automation.

Switch on the power supply, pay attention that

there's nobody where the gate is moving.

(fig.

7).