Elsner WS1 Color Manuale - Pagina 2
Sfoglia online o scarica il pdf Manuale per Sistemi di controllo Elsner WS1 Color. Elsner WS1 Color 2.
Anche per Elsner WS1 Color: Istruzione breve (2 pagine)
System > Installation > Channel Order
6.1. Define channel order
Use the arrow keys to scroll through the list.
The selected device is marked in white. On the right-hand side you will receive sta-
tus information (e.g. on/off, open/closed, exhaust air level, error messages) and va-
rious control options (up/down arrow keys or on/off buttons).
The Down and Up buttons are fitted with automatic time functions.
Drives:
The drive can be precisely positioned with brief button presses (less than 1 second,
short audio signal). For shutters and roller blinds, only a short step-movement
command is triggered. If the button is pressed for longer than 1 second (higher au-
dio signal: locking signal), the drive moves independently to the end position. A
brief press in the opposite direction stops the drive.
For shades and windows, the movement position is shown in percent above the
Up-/Down buttons (for blinds, also the slat position). For radio motor control units,
the position shown can deviate from the movement position set in the automatic
mode by up to 2%.
Ventilation units WL400 and WL800:
Ventilation units WL400 and WL800 are operated in 10% steps by briefly pressing
the button (less than 1 second, brief sound, 10 ventilation levels). By pressing the
button longer, the fan speed is changed continuously. Release the button to stop
speed change.
Note: In rare cases, radio disturbances can lead to continuing speed change after
having released the button. Please briefly press the other direction then.
Speed higher
Fan OFF
(stopped,
Speed lower
press
Extraction Mode
press
Recirculation
Speed lower
Speed higher
Block because of rain, wind or frost alarm:
If a drive group is momentarily blocked for manual operation by a rain, wind or
frost alarm, the arrow keys will be greyed out and may not be used. The message
"Rain alarm" and/or "Wind alarm" is shown.
The frost alarm can be deactivated by pressing the corresponding button (see dia-
gram); manual operation is then possible again. The frost block will then be first
active for this drive again when it is reactivated manually or the next time the frost
alarm is triggered.
ATTENTION
Material damage due to movement of frozen shading
elements!
The drive and hangings may be damaged if a firmly frozen outdoor
shading is moved!
•
Make shure the rails are no longer frozen before manually
switching
off the frost alarm.
Manu
Auto
Whether a drive or device is in automatic mode or manually operated can be re-
cognised from the white marking on the buttons on the right and the text "Auto"
next to the name button in the list on the left. By pressing the button you can switch
from one to another.
After being operated manually the drive or device remains in manual mode. The
automatic functions are thus switched off and only the rain and wind protection
will be carried out. The equipment will only switch back into automatic mode when
reset by hand ("Manu" button) or through the daily automatic reset. In the Auto-
matic menu, the automatic reset can be activated separately for each drive group
and each device.
Automatic Reset
This button allows you to perform the automatic reset manually. All systems for
which an automatic reset has been set are then set to automatic mode.
Back to the weather data display (starting image)
Control System WS1 Style / WS1000 Style
Slideshow
The WS1 Style / WS1000 Style can play back digitally-stored image data as a
slideshow. For this, the image data must be saved onto an SD card and fulfil the
following requirements:
•
Data format Bitmap (BMP)
•
Size 640 x 480 pixels
•
Color intensity 24 bit or 16 bit
•
No compression (RLE)
•
The data must be saved in the uppermost level of the card's directory (root
directory)
Wall
The SD card is pushed into the slot, until it clicks into place.
The card will automatically be recognised. If image data are stored on the card, the
symbol for „play-back" appears at the bottom right-hand side of the weather data
display.
Press „play-back" to start the slideshow.
The image changes approx. every 45 seconds (for images with 24-bit color inten-
sity). To return to the weather data display, touch the screen or remove the SD card
(briefly press down on the card so that it pops out).
Further information about the image display can be found in chapter
6.2. Using an SD card
Navigation in the System menu
All settings for drives and devices, for the automation and the control system are
changed in the System menu, which you reach via the System button:
In three sub-menus you can carry out the following adjustments:
Installation:
•
Specify fundamental characteristics of the drives at inputs/outputs
•
Set up wireless connections to devices
•
Define the order in which the drives and devices are shown (e.g. in the
manual menu)
Automatic settings:
•
Define automatic functions for the individual drives and devices
•
Adjust general automatic settings: Twilight value, movement delays, forced
closure, ventilation block and automatic reset
Control Settings:
•
Change personal data such as Time/Date and location and adjust the screen
display to your personal preferences
•
Restart the control unit, reset to factory defaults and change internal settings
•
Set an access code to protect the "Installation" and "Automatic Settings"
menus from unauthorised changes.
The following buttons are needed constantly for navigation in the System menu:
Back to the previous menu level (only settings already saved
with OK will be applied)
Back to the weather data display (starting image)
Confirms (saves) adjustments made
Info button: Appears in many menus next to the option settings.
Press the button for an explanation of the function shown in the
upper display area. Press again for the explanation to disappear.
Control System WS1 Style / WS1000 Style • Version: 24.10.2023 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de • Technical Service: +49 (0) 7033 / 30945-250
The SD card slot can be found
on the inner face of the housing.
The display is held on the wall
by magnets. It is connected to
the power electronics in the
concealed box with a cable. Lift
the display unit to the front wit-
hout breaking the cable connec-
tion.
On the top right, beneath the System field, is shown which menu you are currently
in as well as the path by which you arrived there. For example, if you are in the Au-
tomation menu for the light intensity of the "South awning", the path will be:
System > Automation > Awning > Awning South > Intensity
Change language
The menus can be shown in German, English, French or Italian. Press the buttons:
WS1 / WS1000
Settings
Settings
System
Language
Select the desired language for the menues by pressing the button. Confirm your
setting with the OK button.
Switch on/off button tone
The sound that is played as a feedback when a button is pressed can be switched off or on again.
Press the buttons:
WS1 / WS1000
Settings
Settings
System
Button tone
In the appearing menu, you can switch on or off the button tone. Press the button
On or Off. Pre-set: On.
Select time zone
In order to display date and time correctly, the time zone (relating to GMT) must be
specified here. In addition the automatic switch-over to summer time can be set.
You can reach the time zone settings by pressing the buttons:
WS1 / WS1000
Settings
Settings
System
Time zone
The time zone can be set by pressing the arrow keys in the menu that appears.
Press the button next to Summertime Rule to set the automatic switch-over. De-
pending on location, select Europe, USA, None (if no summertime switch-over
shall take place) or User-defined (if the switching shall be set individually).
Confirm your setting with the OK button.
2