Datalogic S51-PR Series Manuale di istruzioni

Sfoglia online o scarica il pdf Manuale di istruzioni per Accessories Datalogic S51-PR Series. Datalogic S51-PR Series 5.

Stampa la pagina

Datalogic S51-PR Series Manuale di istruzioni

This product is covered by one or m ore of the following patents.

European Patent 1,111,690 B1

S51-PA/PR SERIES

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (S51-...A00/B01/C01/C10/F00)

T he yellow LED ON indicates that the NO output status is closed.

POWER ON LED (S51-...G00)

T he green LED indicates that the sensor is operating.

TRIMMER (S51-...B01/C01)

T he trimmer can be used to adjust sensitivity; the operating distance

increases turning the trimmer clockwise.

WARNING: The trimmer rotation is limited to 270°.

Do not apply excessive torque beyond the maximum and minimum

positions (max 40 Nmm).

INSTALLATION

The sensor can be fixed by means of the M18x1 threaded body through a

 18mm hole, using the specific washer and the two CH.24 nuts (1.5Nm

maximum tightening torque) or CH.22 nuts, h=8mm, (2Nm maximum

tightening torque) enclosed. Alternatively, the sensor can be mounted

through the two housing's holes using two screws (M3x22 or longer)

and washer.

Amongst the various possible solutions, we suggest to choose the

combination that offers the best visibility of the signalling LEDs and the

easiest access to the trimmer.

Various orientable fixing brackets are available

to ease the sensor positioning (please refer to

the

accessories

listed

the general

catalogue).

The

operating

distance

measured from the front surface of the sensor

lens.

C m odels: To improve the detection, the object

has to be moved closer or further away from the front surface of the

sensor lens.

In case of lateral translation, the object must move as indicated in the

figure.

CONNECTIONS

The connections are compliant to the EN 60947-5-2 standard.

S51-...A00/B01/C01/C10/F00

S51-...G00

BROWN

10 ... 30 Vdc

WHITE

DARK- / LIGHT+

BLACK

N.O. OUTPUT

BLUE

0 V

in case of white wire or pin 2 not connected the sensor works in LIGHT

mode for proximity models (C01/C10/C20) and in DARK mode for

retroreflex (A00/B01) and receiver (F00).

M12 CONNECTOR

AXIAL VERSION

1.5

3.5

2.5

TRIMMER

N°.2 Ø3.8

OUTPUT LED

CH.24 PLASTIC NUTS

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating temperature:

Storage temperature:

Insulating strength:

Insulating resistance:

Operating distance

(typical values):

10 ... 30 Vdc

Emission type:

TEST +

Ambient light rejection:

TEST -

Vibrations:

Shock resistance:

0 V

white wire or pin 2 connected to +10...30V LIGHT mode; to 0V DARK mode

LIGHT/DARK selection:

white wire or pin 2 not connected

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

AtEx 2014/34/EU

DIMENSIONS

M O D E L S

RADIAL VERSION

with trimmer

without trimmer

14.5

1.5

3.5

CABLE VERS.

14.5

STABILITY LED

OUTUPT LED

CH.22 PLASTIC NUTS

TECHNICAL DATA

S51-PA AXIAL VERSION

10 ... 30 Vdc (limit values)

2 Vpp max.

30 mA max.

N.O.; PNP or NPN (short circuit protection)

100 mA max.

2 V max.

1 ms (4 ms mod.F00)

500 Hz (120 Hz mod.F00)

OUTPUT LED (YELLOW) mod.G00 excluded

POWER ON LED (GREEN) (mod.G00)

sensitivity trimmer (mod.B01/C01)

-25 ... 55 °C

-25 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 M 500 Vdc, between electronics and housing

A00: 0.1...3.5 m on R2

B01: 0.1...2.5 m on R2

C01: 1...40 cm

C10: 0...10 cm

F00/G00: 0...18 m

RED (660 nm) (mod.B01) / INFRARED (880 nm) (mod.A00/C01/C10/G00)

according EN 60947-5-2

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

LIGHT mode (mod.C01/C10);

DARK mode (mod.A00/B01/F00)

PBT

PMMA

IP67

2 m cable  4 mm / M12 - 4 pole connector

75 g. max. cable vers. / 25 g. max. connector vers.

I I 3G EX nA II T6 ;

I I 3D EX tD A22 IP67 T85°C

Setting of S51-...A00/B01

M O D E L S

with trimmer

without trimmer

Position the sensor and reflector on opposite sides.

14.5

Moving the sensor both vertically and horizontally, determine the power

on and off points of the yellow LED (OUT) and then mount the sensor in

the middle of the points defined.

B01 Model: Turn the sensitivity trimmer to the maximum position.

If necessary reduce sensitivity in order to detect very small targets. In

order to improve alignment, repeat the procedure detailed above whilst

progressively reducing the sensitivity.

CABLE VERS.

Setting of S51-...F00/G00

TRIMMER

Position the sensors on opposite sides.

Move the sensor both vertically and horizontally, determine the power on

and off points of the yellow LED (OUT) and then mount the sensor in the

N°.2 Ø3.8

STABILITY LED

middle of the defined points.

OUTPUT LED

Setting of S51-...C01

Turn the sensitivity trimmer to minimum: the yellow LED

is OFF.

Position the target to detect in front of the sensor.

Turn the sensitivity trimmer clockwise until the yellow

LED turns ON (Target detected state, pos.A).

Remove the target, the yellow LED turns OFF.

Turn the sensitivity trimmer clockwise until the yellow LED turns ON

(Background detected state, pos.B).

The trimmer reaches the maximum level if the background is not

detected.

S51-PR RADIAL VERSION

Turn the trimmer to the intermediate C position, between the two A and B

positions.

Setting of S51-...C10

The operating distance range of these sensors is factory preset: please

consider this feature when positioning.

The TEST+ and TEST- inputs can be used to inhibit the emitter and

verify that the system is correctly operating.

The receiver output should switch when the test is activated while the

beam is uninterrupted. The inputs activating voltage range is 10 ... 30

Vdc, whilst respecting the polarity.

The emission is switched off connecting TEST+ to Vdc and TEST- to

0V.

A00: 0.1...2.5 m on R2

B01: 0.1...2.0 m on R2

C01: 1...30 cm

C10: 0...8 cm

F00/G00: 0...15 m

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions, Support.

The warranty period for this product is 36 months. See General Terms and Conditions of

Sales for further details.

limiting the rights under copyright, no part of this documentation may be reproduced, stored in

or introduced into a retrieval system, or transmitted in any form or by any means, or for any

purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many

countries, including the U.S.A. and the E.U. All other trademarks and brands are property of

their respective owners. Datalogic reserves the right to make modifications and improvements

without prior notification.

SETTING

MAX

MIN

TEST FUNCTION (S51-...G00)

EX-II-3-D T6

T6 (<85°C)

Temperature class:

Max. Power consumption:

900 mW at 30 Vdc

Max. Internal capacitance:

170 nF

Internal inductance:

negligible

For information about the disposal of Waste Electrical and Electronic

Equipment (WEEE), please refer to the website at www.datalogic.com.

826002973 Rev.E