Dustless 16011 Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Aspirapolvere Dustless 16011. Dustless 16011 9. 16 gallon wet/dry vacuum hepa vacuum, and toolsync tool activated vacuum

Stampa la pagina

To install the legs and accessory tray, undo the clips holding the intermediate cover in place and set the cover and lid assembly

aside. Turn tank upside down. Front legs are on either side of the drain port opening. These front legs do not have the small hooks

on either side. The back legs do have the hooks. These hooks are for the hose to rest on when in storage.

lign legs with openings provided on bottom of the canister and slide into place. The holes will only align in proper position

for front and back legs. Insert black support screw into hole and tighten screw with a Phillips screwdriver.

Turn cleaner tank right side up.

ttach ccessory Tray

lign the three slots on the edge of the accessory tray with the three guides on the rear side of

the tank and press the accessory tray toward the tank as you push the tray down. The two lock-

ing tabs will slide under the rim of the tank and catch. By pushing the tray down and toward

the tank it will lock into place.

Place intermediate cover and lid assembly right side up and set on top of the tank.

ttach the yellow clips from the tank onto the intermediate cover.

The Lid ssembly with the vacuum controls, motor, and filters are all preassembled at the

factory for your convenience. Maintenance and replacement of filters is described later in

this manual.

ttach hose, wands and cleaning accessories

Hose and accessories are stored on the unit. The hose will loop through the two outside holes of the

accessory tray and rest on the hooks of the back legs as shown below. For convenience, additional

accessories can be stored on tray when not in use.

To Use ccessories

Push hose into tank port; twist hose to tighten or loosen connection. The wands and cleaning accessories attach to hose in the same manner.

Dustless Technologies Model 16003 Wet/Dry Vacuum delivers 99% filtration at .5 micron which is great for fine particle pick-up, like

drywall, concrete, or surface dust. ll units come with a powerful 11 amp motor, dual filtration system, corrosion resistant tank, large

wheels and an integrated accessory holder. Model 16010 comes with a built-in ToolSync outlet for use with power tools providing an

automatic vacuum start-up when the tool is turned on and about a 6 second shut-off delay to clear the hose when the vacuum is

turned off. Model 16006 Wet/Dry Vacuum has HEP certified filters installed and provides filtration rated at D.O.P Eff. Mil. Std. 282:

99.97% min. at .3 micron. The Model 16011 HEP Wet/Dry Vacuum comes with ToolSync.

The ToolSync model vacuums (16009, 16010, 16011) are intended for use with small hand held power tools with current rating 8

amperes or less. ccessories are available to allow larger tools to operate with the vacuum. See the ToolSync Operation section below

for more information.

SSEMBLY

GENER L INFORM TION

utomatic Suction Shut-Off

NOTE: The unit must be used in the upright position at all times, otherwise the automatic suction

shut-off will activate. The automatic suction shut-off functions when the tank fills with liquid. s

the tank fills, the ball float ( inside the cage ) rises until it seats itself against the bottom of the

intermediate cover. This shuts off the suction of the vacuum cleaner when the tank is full.

ToolSync Vacuum Controls (Models 16009, 16010 and 16011)

Wireless remote

start plug

Vacuum ToolSync outlet

Note: Model 16009 comes without the

Vacuum ToolSync outlet and Wireless

remote start plug

I – Continuous run mode.

0 – Off

II – utomatic or ToolSync

mode. Power is supplied to

outlet, vacuum will start

Power cord

when tool activates.

No power to outlet