COOK Economizer Manuale di installazione, funzionamento e manutenzione
Sfoglia online o scarica il pdf Manuale di installazione, funzionamento e manutenzione per Cappa di ventilazione COOK Economizer. COOK Economizer 8.
Stampa la pagina
®
This publication contains the installation, operation and
maintenance instructions for standard units of the Economizer
Fan - Economizer Fans with Mix, Recirculate, Supply and
Exhaust Modes.
Carefully read this publication and any
supplemental documents prior to any
installation or maintenance procedure.
Loren Cook catalog, Economizer Fan, provides additional
information describing the equipment, fan performance, avail-
able accessories and specification data.
For additional safety information, refer to AMCA Publication
410-96, Safety Practices for Users and Installers of Industrial
and Commercial Fans.
All of the publications listed above can be obtained from:
• lorencook.com
• 417-869-6474 ext. 166
For information and instructions on special equipment, con-
tact Loren Cook Company at 417-869-6474.
Receiving and Inspection
Carefully inspect the fan and accessories for any damage
and shortage immediately upon receipt of the fan.
The control panel, if ordered, is shipped inside of the roof
base. It is not counted as a separate part.
• Turn the propeller by hand to ensure it turns freely and does
not bind
• Check the dampers for free operation of all moving parts
• Record on the Delivery Receipt any visible sign of damage
Handling
Lifting bars are located on the top of the cabinet assembly.
They should be used to lift the unit and also to lower the unit
on to the curb. The hood assembly should be lifted by the
shipping crate or the base.
Economizer
ECONOMIZER IO&M
ECONOMIZER FAN
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
Rotating Parts & Electrical Shock Hazard:
Fans should be installed and serviced by qualified personnel
only.
Disconnect electric power before working on unit (prior to re-
moval of guards or entry into access doors).
Follow proper lockout/tagout procedures to ensure the unit
cannot be energized while being installed or serviced.
A disconnect switch should be placed near the fan in order
that the power can be swiftly cut off, in case of an emergency
and in order that maintenance personnel are provided com-
plete control of the power source.
Grounding is required. All field-installed wiring must be com-
pleted by qualified personnel. All field installed wiring must
comply with National Electric Code (NFPA 70) and all appli-
cable local codes.
Fans and blowers create pressure at the discharge and vac-
uum at the inlet. This may cause objects to get pulled into the
unit and objects to be propelled rapidly from the discharge.
The discharge should always be directed in a safe direction
and inlets should not be left unguarded. Any object pulled into
the inlet will become a projectile capable of causing serious
injury or death.
When air is allowed to move through a non-powered fan, the
impeller can rotate, which is referred to as windmilling. Wind-
milling will cause hazardous conditions due to unexpected ro-
tation of components. Impellers should be blocked in position
or air passages blocked to prevent draft when working on fans.
Friction and power loss inside rotating components will cause
them to be a potential burn hazard. All components should be
approached with caution and/or allowed to cool before con-
tacting them for maintenance.
Under certain lighting conditions, rotating components may
appear stationary. Components should be verified to be sta-
tionary in a safe manner, before they come into contact with
personnel, tools or clothing.
Failure to follow these instructions could result in death or se-
rious injury.
The attachment of roof mounted fans to the roof curb as well
as the attachment of roof curbs to the building structure must
exceed the structural requirements based on the environmen-
tal loading derived from the applicable building code for the
site. The local code official may require variations from the
recognized code based on local data. The licensed engineer
of record will be responsible for prescribing the correct attach-
ment based on construction materials, code requirements and
environmental effects specific to the installation.
1
Economizer Fans
B51132-003