Bender COMTRAXX COM465ID Manuale di avvio rapido - Pagina 4
Sfoglia online o scarica il pdf Manuale di avvio rapido per Monitor Bender COMTRAXX COM465ID. Bender COMTRAXX COM465ID 4. Condition monitor with integrated gateway
Anche per Bender COMTRAXX COM465ID: Avvio rapido (4 pagine), Manuale di avvio rapido (4 pagine)
Stampa la pagina
Gerät in Betrieb nehmen
1. Das COM465ID per Ethernetkabel (RJ45) direkt mit
einem PC verbinden.
2. Alle angeschlossenen Geräte einschalten.
3. Internetbrowser auf dem PC starten.
4. Folgende Adresse im Internetbrowser eingeben:
169.254.0.1
5. Links in der NavigationBUSÜBERSICHT anklicken.
6. Die Kachel des COM465ID auswählen.
7. Etherneteinstellungen konfigurieren
Menü > Einstellungen > Schnittstelle > Ethernet
8. Nach erfolgreicher Konfiguration das Gerät mittels
RJ45 in das LAN einbinden.
Technische Daten
Bemessungsspannung .............................................................. AC 250 V
Bemessungs-Stoßspannung ..............................................................4 kV
Überspannungskategorie ..................................................................... III
Verschmutzungsgrad ..............................................................................3
Sichere Trennung (verstärkte Isolierung) zwischen
......................................(A1/+, A2/-) –[(AID1, BID1), (AID2, BID2), (X2)]
Versorgungsspannung U
............................................ AC/DC 24...240 V
S
Frequenzbereich U
...........................................................DC, 50...60 Hz
S
Eigenverbrauch ...............................................................≤ 6,5 VA/≤ 4 W
Ethernet
Anschluss .............................................................................. RJ45
Datenrate ............................................10/100 MBit/s, autodetect
DHCP ................................................................................ein/aus
isoData
Schnittstelle/Protokoll ........................................RS-485/isoData
Betriebsart ........................................................................Master
Baudrate ........................................................................9,6 kBit/s
Leitungslänge ...............................................................≤ 1200 m
Arbeitstemperatur .............................................................–25...+55 °C
Schutzart (IEC 60529)................................................................................
Einbauten .............................................................................. IP30
Klemmen .............................................................................. IP20
Bender GmbH & Co. KG
Londorfer Straße 65
35305 Grünberg
Germany
Tel.: +49 6401 807-0
www.bender.de
Commissioning the device
1. Connect the COM465ID directly to a PC via an
2. Switch on all connected devices.
3. Start an internet browser on the PC.
4. Enter the following address in the Internet browser:
5. Click on the left hand side in the navigation
6. Select the COM465ID tile.
7. Configure the Ethernet settings
8. After successful configuration, connect the device
Technical data
Rated voltage .............................................................................AC 250 V
Rated impulse withstand voltage ......................................................4 kV
Overvoltage category ........................................................................... III
Pollution degree ....................................................................................3
Protective separation (reinforced insulation) between
......................................(A1/+, A2/-) –[(AID1, BID1), (AID2, BID2), (X2)]
Supply voltage U
Frequency range U
Power consumption ........................................................≤ 6.5 VA/≤ 4 W
Ethernet
isoData
Operating temperature ......................................................–25...+55 °C
Degree of protection (IEC 60529) ..............................................................
Alle Rechte vorbehalten.
Nachdruck und Vervielfältigung nur mit
Genehmigung des Herausgebers.
All rights reserved.
Reprinting and duplicating only with
permission of the publisher.
ethernet cable (RJ45).
169.254.0.1
BUS OVERWIEW.
Menu > Settings > Interface > Ethernet
to the LAN via RJ45.
........................................................ AC/DC 24...240 V
S
...........................................................DC, 50...60 Hz
S
Connection ............................................................................ RJ45
Data rate .............................................10/100 MBit/s, autodetect
DHCP ..................................................................................on/off
Interface/protocol ...............................................RS-485/isoData
Operating mode ................................................................Master
Baud rate .......................................................................9.6 kBit/s
Cable length ..................................................................≤ 1200 m
internal components ............................................................. IP30
terminals ............................................................................... IP20
© Bender GmbH & Co. KG, Germany
Subject to change! The specified
standards take into account the edition
valid until 09/2023 unless otherwise
indicated.