BENDIX LQ-3 LQ-4 FRONT AXLE RATIO VALVE Manuale - Pagina 5
Sfoglia online o scarica il pdf Manuale per Unità di controllo BENDIX LQ-3 LQ-4 FRONT AXLE RATIO VALVE. BENDIX LQ-3 LQ-4 FRONT AXLE RATIO VALVE 8. Front axle ratio valve
Stampa la pagina
WASHER
(2)
RETAINING
RING
(1)
™
FIGURE 8 - LQ-3
FRONT AXLE RATIO VALVE INNER
PISTON ASSEMBLY
CLEANING AND INSPECTION
1. Wash all metal parts in mineral spirits and dry them.
2. Inspect all parts for excessive wear or deterioration.
3. Inspect the valve seat for nicks or burrs.
4. Check the spring for cracks or corrosion.
5. Replace all rubber parts and any part not found to be
serviceable during inspection, using only genuine Bendix
replacement parts.
ASSEMBLY
Prior to reassembling the LQ front axle ratio valve, lubricate
all o-rings, o-ring grooves, piston bores and metal moving
surfaces with Bendix silicone lubricant piece number 291126
(Dow Corning 650-M).
1. (LQ-3
™
valve — Figure 8) Place the inlet and exhaust
valve (4), valve spring (3), and washer (2) in the inner
piston. Install the retaining ring (1) in the piston, making
certain it is completely seated in its groove.
™
(LQ-4
valve — Figure 7) Place the inlet and exhaust
valve (10) and spring (9) in the inner piston (3). The spring
must be carefully located under the shoulder in the
inner piston.
2. Install the large (8) and small (7) diameter o-rings in
their grooves on the inner piston.
3. Install the o-ring (6) on the outer piston.
4. Insert the inner piston into the bore of the outer piston.
Note: See Figure 7 for proper inner and outer piston
configuration after assembly.
5. Place the outer piston spring (5) in the valve body and
the hold-off spring (11) if used.
6. Install the inner and outer piston assembly in the body
through the spring (see Figure 7).
INLET-EXHAUST
VALVE (4)
INLET
EXHAUST
SPRING (3)
7. Place the cover over the body in the proper position, as
marked in Step 1 of the Disassembly procedure.
8. Using the four Phillips head screws and lockwashers,
secure the cover to the body. Torque the screws to
50-80 inch pounds.
TESTING THE REBUILT LQ-3
FRONT AXLE RATIO VALVE
™
Test the rebuilt LQ-3
or LQ-4
performing the operational and leakage tests outlined in the
Service Checks section of this manual.
WARNING! PLEASE READ AND FOLLOW
THESE
INSTRUCTIONS
PERSONAL INJURY OR DEATH:
When working on or around a vehicle, the following
general precautions should be observed at all times.
1. Park the vehicle on a level surface, apply the
parking brakes, and always block the wheels.
Always wear safety glasses.
2. Stop the engine and remove ignition key when
working under or around the vehicle. When
working in the engine compartment, the engine
should be shut off and the ignition key should be
removed. Where circumstances require that the
engine be in operation, EXTREME CAUTION should
be used to prevent personal injury resulting from
contact with moving, rotating, leaking, heated or
electrically charged components.
3. Do not attempt to install, remove, disassemble or
assemble a component until you have read and
thoroughly understand the recommended
procedures. Use only the proper tools and observe
all precautions pertaining to use of those tools.
4. If the work is being performed on the vehicle's air
brake system, or any auxiliary pressurized air
systems, make certain to drain the air pressure from
all reservoirs before beginning ANY work on the
vehicle. If the vehicle is equipped with an AD-IS
air dryer system or a dryer reservoir module, be
sure to drain the purge reservoir.
5. Following
the
recommended procedures, deactivate the electrical
system in a manner that safely removes all
electrical power from the vehicle.
6. Never exceed manufacturer's recommended
pressures.
7. Never connect or disconnect a hose or line
containing pressure; it may whip. Never remove a
component or plug unless you are certain all
system pressure has been depleted.
8. Use only genuine Bendix
components and kits. Replacement hardware,
tubing, hose, fittings, etc. must be of equivalent
size, type and strength as original equipment and
be designed specifically for such applications and
systems.
™
AND LQ-4
™
™
front axle ratio valve by
TO
AVOID
vehicle
manufacturer's
®
replacement parts,
™
5