Gage Bilt GB110A/2 Manuale di istruzioni originale - Pagina 11

Sfoglia online o scarica il pdf Manuale di istruzioni originale per Strumenti Gage Bilt GB110A/2. Gage Bilt GB110A/2 17. 20v battery installation tool

Stampa la pagina

WARNING:

Only qualified and trained operators should install, adjust or use the installation power tool for all fasteners.

WARNING:

Operator

WARNING:

It is required that eye protection, hearing protection and safety boots be worn at all times while handling this equipment.

WARNING:

The users or the user's employer should assess specific risks that could be present before each use based on their application.

●

Be sure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any

moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.

●

Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool

WARNING:

Do not pull fastener in the air. Personal injury from fastener ejecting may occur.

WARNING:

Do not use as a hammer. If improperly used or damaged, liquid can escape from the battery causing skin irritations

or burns. Wash with water or seek medical attention immediately if liquid gets into eyes or burns occur.

WARNING:

Do not use in explosive atmosphere.

WARNING:

Charge the batteries only in chargers recommended by the manufacturer. Risk of fire or explosion if batteries

used on non manufacturer chargers.

WARNING:

Use only the specified batteries in the tool. The use of other batteries could result in injury or fire.

WARNING:

Keep battery (VP1086/VP1357), when not in use, away from paper clips, coins, keys, nails, screws, or other small metal

objects that could cause bridging of the contacts. A short circuit between the battery contact can cause burns or fire.

WARNING:

Never operate the installation tool without the mandrel collection bottle (VP1356) or cover cap (VP1321).

WARNING:

By-passing the safety switch is prohibited. Do not use if switch is defective or can no longer be turned on or off.

WARNING:

Do not use cover cap (VP1321) with non self releasing nose assemblies. Damage to tool will occur.

WARNING:

Ensure the mandrel collection bottle (VP1356) / cover cap (VP1321) are properly connected and used correctly.

WARNING:

Avoid inadvertent starting of the installation tool.

WARNING:

Having your finger on the actuator assembly (VP1316) while carrying the installation tool can lead to accidents.

CAUTION:

Check that the hanger clip (VP1322) is securely fitted before using the tool. Ensure the clip is not stretched too

far apart and loses its tension.

CAUTION:

Do not use beyond the design intent.

CAUTION:

Remove the battery (VP1086/VP1357) before making adjustments to the tool, changing accessories, or putting

tool away. This precautionary measure prevents any unintentional starting of the installation tool.

Working with the Installation tool (GB110A):

Insert the mandrel of the fastener into the nose assembly.

Note: Tool will not function without the mandrel collection bottle (VP1356) or cover cap (VP1321) attached.

Now insert the fastener into the parts to be fastened. For a good fastening result, ensure that the parts and head of the fastener

are resting on one another without a gap.

Press the actuator assembly (VP1316) until the mandrel is sheared.

Hold the installation tool so that the mandrel collection bottle (VP1356) is facing downwards to ensure that the sheared mandrel

drops into the mandrel collection bottle (VP1356).

When working with the cover cap (VP1321), hold the installation tool with the nose assembly facing downwards after each set

fastener to ensure that the sheared mandrel drops out of the installation tool to the front. DO NOT use cover cap (VP1321) with

non-self releasing nose assemblies. This would result in damage to the tool.

Lockbolts

1. Insert fastener through the work piece.

2. Slide collar over fastener.

Note: Always hold tool so pulling head is perpendicular to surface

of material in which fastener is being installed. Exert firm

pressure against fastener during installation.

3. Insert fastener into nose assembly.

4. Press actuator to start cycle.

5. Release actuator as soon as fastener breaks.

6. Repeat steps 1-5.

GB110A 20V BATTERY INSTALLATION TOOL

HOW TO USE THE GB110A

MUST

read and understand all warnings and cautions.

Blind Fasteners

1. Insert fastener into workpiece.

2. Insert fastener into nose assembly.

Note: Always hold tool so pulling head is perpendicular to surface

of material in which fastener is being installed. Exert firm

pressure against fastener during installation.

3. Press actuator to start cycle.

4. Release actuator as soon as fastener breaks.

5. Repeat steps 1-4.

Images may not reflect

actual tool or fastener

8/18 REV 8/22