Gage Bilt GB744 Manuale di installazione - Pagina 7
Sfoglia online o scarica il pdf Manuale di installazione per Utensile elettrico Gage Bilt GB744. Gage Bilt GB744 13.
FILLING AND BLEEDING TOOL
NOTE:
Air bleeder assy (704153) is required.
WARNING:
Do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (S572),
installed in the head cylinder assy (744103). Severe personal injury may result.
CAUTION:
Before filling handle assy (744129), the air piston assy (744121) should be all the way down.
CAUTION:
When forcing piston rod assy (704136) downward with head cylinder assy (744103) removed, hydraulic oil will
eject forcibly from handle assy (744129).
CAUTION:
Use CAUTION when removing button head cap screws (402482), stat-o-seals (S572) and air bleeder assy (704153).
Hydraulic oil may be under pressure
WARNING:
Failure to follow these instructions carefully may result in severe personal injury
To replace a small amount of oil in the tool, attach the air bleeder assy (704153) and connect tool to air line. Cycle tool ten times.
Disconnect air, remove the air bleeder assy (704153), and reinstall the button head cap screw (402482) and stat-o-seal (S572) on the
head cylinder assy (744103). This will ensure the removal of any air from the hydraulic system and its replacement with oil.
Should it become necessary to completely refill the tool (such as would be required after tool has been dismantled and reassembled),
take the following steps after depressing air actuator assy (704130)
1. Remove four button head cap screws (402479) and head cylinder assy (744103) from handle assy (744129). Slowly push piston
(744409) completely forward.
2. Fill handle assy (744129) and the oil passage on top of handle assy (744129) with automatic transmission oil, Dexron III or
equivalent. When looking at the top of the handle assy (744129), the oil passage is the hole that is counterbored for o'ring (S832).
3. Replace head cylinder assy (744103) with care, ensuring gasket (704129) and o'ring (S832) are properly installed. Torque button
head cap screws (402479) uniformly to 40 inch lbs. to prevent leakage around gasket (407129).
4. Remove button head cap screw (402482) and stat-o-seal (S572) from head cylinder assy (744103). Install air bleeder assy
(704153) and connect tool to air line. Cycle ten times to fully circulate oil through hydraulic system.
5.
DISCONNECT AIR FROM
(S572) on head cylinder asssy (744103). Torque 35-40 inch lbs. (Do NOT over-tighten).
6. Connect air supply. Cycle tool ten times and check stroke of .580" (14.73mm) (see diagram below). We recommend using a pair of dial
calipers. With the air actuator assy (704130) released, check dimension (A). With the air actuator assy (704130) depressed, check
dimension (B). Subtract dimension (A) from dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 4-6.
.48 (12.1mm)
TROUBLESHOOTING
Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.
1. MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET.
a)
Tool needs to be bled. (See filling and bleeding instructions.)
b)
Spring has fatigued, replace.
c)
Jaws are stripped or packed with chips. Clean or replace.
d)
Incorrect nose tip.
2. SLOW OR PARTIAL OPERATION WHEN THE AIR ACTUATOR ASSY (704130) IS DEPRESSED
a)
Polyseal (A-1135) and o'ring's (400792) on piston (744409) could be worn or damaged. Replace.
b)
Back-up Ring (S908) and o'ring (A-201) on piston rod assy (740136) could be worn or damaged. Replace.
c)
Muffler (744143) or filter inside valve spool assy (743142) may be plugged with dirt. Clean thoroughly and back-blow
with compressed air.
d)
Hole in metering screw in valve spool assy (743142) may be blocked or damaged. Hole diameter should be .028". Clear
and size or replace.
3. NO OPERATION WHEN AIR ACTUATOR ASSY (704130) IS DEPRESSED
a)
Tool seized due to mechanical failure or damaged parts.
4. OIL LEAKAGE
a)
DO NOT
OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.
b) Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.
5. AIR BYPASS FROM VALVE HOUSING
a)
If the spring (744144) breaks or dislodges, air will flow freely through the muffler (744143). Replace or reset. Valve
spring installation tool (704153) is recommended.
b)
Check o'rings on valve sleeve (743144), valve spool assy (743142), and valve plug (744142). If worn or damaged,
replace. Valve sleeve removal tool (744152) is recommended.
6. FASTENER STEM JAMMED IN NOSE ASSEMBLY
a)
Nose assembly components require service.
disassemble. Replace worn or broken parts. Clean the surface the jaws ride on.
b)
Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.
c)
Incorrect follower.
.
TOOL. Remove air bleeder assy (704153) and install button head cap screw (402482) and stat-o-seal
"A"
AND DISCONNECTING THE AIR SUPPLY:
DISCONNECT AIR FROM
7
"B"
1.06 (26.9mm)
TOOL, remove the nose from the tool and
Rev. 2/15