Gage Bilt GB568 Manuale di istruzioni originale - Pagina 8
Sfoglia online o scarica il pdf Manuale di istruzioni originale per Strumenti per rivetti Gage Bilt GB568. Gage Bilt GB568 20. Installation tool
Anche per Gage Bilt GB568: Manuale di istruzioni originale (16 pagine)
Stampa la pagina
WARNING:
Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded
mechanical fasteners.
WARNING:
Operator
WARNING:
It is required that eye protection, hearing protection and safety boots be worn at all times while handling this
equipment.
WARNING:
The users or the user's employer must assess specific risks that could be present as a result after each use
based on their application.
●
Ensure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any
moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.
● Verify
●
Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool
WARNING:
Do not actuate fastener in the air. Personal injury from fastener ejecting may occur.
WARNING:
Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other
persons working in the vicinity, foreign matter and liquid.
WARNING:
Do not carry from hoses or use as a hammer.
WARNING:
Do not use in explosive atmosphere.
WARNING:
Ensure air hose is securely connected to avoid possible hose whipping.
WARNING:
Always disconnect air supply when tool is not in use to prevent accidental start-up.
WARNING:
Ensure there is adequate clearance for tool and operator hands.
WARNING:
Incorrect stroke will damage the nose assembly.
WARNING:
Do not dry cycle or actuate tool without fastener in place. Damage to the nose assembly could occur.
CAUTION:
Do not use beyond the design intent.
The tool is shipped with a red plastic plug in the air inlet connector. The connector has a 1/4-18 female pipe thread to accept user air
hose fitting. The tool comes with oil and is ready to use.
1. Remove red plastic shipping plug from Swivel (A-249) (air inlet) and screw in your quick disconnect (air) fitting.
2. Connect tool to air hose with 85 psi. (5.9 bar) min. using clean, dry air. 3/8" (9.52 mm) minimum diameter air line is recommended.
3. Set stroke in accordance to nose assembly and fastener. (See checking & adjusting stroke pg. 20).
(See
WARNINGS
listed above regarding incorrect stroke & NOT to dry cycle tool).
4. Connect air supply. (Tool must be connected to airline before nose assembly is attached).
5. Attach nose assembly. (See
5a. Remove retaining ring (401493), sleeve (568103) and
split-ring (568101). (See pg. 13 for ref.).
5b. Insert jaw and retainer assembly into stationary jaw.
5c. Slide retaining ring (401493) first and sleeve (568103) second over the rear
side of the stationary jaw. Place assembled nose assembly flush to face of
tool while inserting jaw and retainer assembly into piston of tool.
5d. Place split rings (568101) with the side containing the retaining ring
groove around rear of stationary jaw and head cylinder.
5e. Slide sleeve (568103) over split ring (568101) until it stops, attach retaining
ring (401493) into groove of (568101) split ring.
(See proper data sheet for further instructions).
6. Re-connect air line to tool.
USER QUICK
DISCONNECT
FITTING
GB722/568 INSTALATION TOOL
HOW TO SET-UP THE GB722/568
MUST
read and understand all warnings and cautions.
the air lines and/or hydraulic hoses are not a trip hazard.
WARNING
above in
AIR INLET
AIR HOSE
red
text).
NOSE
ASSEMBLY
HEAD CYLINDER
ACTUATOR
Images may not reflect actual tool.
8
5b
5c
5e
Sleeve
NOTE: The nose assembly must be perpendicular
when using as it's important to the life of the
nose assembly.
Split Ring
5d
5e
Retaining Ring
11/21 REV. 5/22