Gaggenau BO 451 930 Istruzioni per l'installazione - Pagina 3

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno Gaggenau BO 451 930. Gaggenau BO 451 930 4.

Stampa la pagina

Ins tal la tion i ns tru cti ons

Important notes

Read these instructions carefully and keep them in a safe

■

place. Safety during use can only be ensured if the appliance

is fitted correctly according to these installation instructions.

The installer is responsible for ensuring that the appliance

operates perfectly at the point of installation.

Only allow a licenced professional to connect the appliance.

■

The appliance must be disconnected from the power supply

■

during all installation work.

Wear protective gloves to prevent injury from cuts. Parts that

■

are accessible during installation may have sharp edges.

Check the appliance for any transport damage before

■

installation.

Do not lift the appliance by the door, door handle or lower air

■

vent.

For installation, currently applicable building regulations and

■

the regulations of the local electricity supplier must be

observed.

This appliance corresponds to appliance class 3 for

■

installation in a kitchen unit according to the installation

drawing. Observe the minimum distances.

Planning notes

Door hinge not reversible.

The door panel surface of the appliance extends 47 mm from

the furniture cavity.

The outer edge of the door handle extends 94 mm from the

furniture cavity.

Consider the overhang, incl. the door handle, when planning to

open drawers next to the appliance.

When planning a corner solution, pay attention to the 90° door

opening angle.

Preparing kitchen units

Fitted units must be heat-resistant up to 90 °C, adjacent cabinet

fronts up to 70 °C.

There must be a ventilation cut-out of min. 20 x 500 mm made

in the intermediate floor of the surround unit.

The appliance connection box must be positioned outside the

installation space.

Carry out all cut-out work on the furniture unit and worktop

before fitting the appliances. Remove any shavings or the

correct operation of electrical components may be impaired.

Secure freestanding units to the wall using standard,

commercially available brackets.

Only fit the appliance up to a height which allows accessories to

be easily removed.

All manuals and user guides at all-guides.com

Electrical connection

Make sure that the household installation has sufficient fuse or

circuit breaker protection. Check that the appliance has the

same voltage and frequency as the electrical installation system

(see rating plate).

The appliance corresponds to protection class 1 and may only

be operated with a protective earth connection.

Fuse protection using B or C circuit breakers is required.

The installation system must incorporate an all-pole isolating

switch with a contact gap of at least 3 mm. This must remain

accessible after installation.

Appliance without mains connection cable: Only connect as

shown on the connection diagram. Fit the enclosed copper

bridges as required. Incorrect connection may cause damage to

the appliance.

Mains connection cable: type H05 VV-F or higher rated. The

yellow/green wire for the PE connection must be 10 mm longer

than the other wires on the appliance side.

The rear of the appliance has tapered edges. When cabinet

depth is 550 mm, the connection lead must be guided down the

rear right side of the cabinet to the connector box.

Fitting the appliance

■

Combination with steam oven

Fit the steam oven first. Follow the installation instructions for the

steam oven.

To achieve the 550 mm installation depth, the water hoses and

connection cable needs to follow the slanted edge on the corner

of the housing.

Combination with warming drawer

Fit the warming drawer first. Follow the installation instructions

for the warming drawer.

Slide the oven into the cabinet, on top of the warming drawer.

When installing the oven take care not to scratch the panel or

the handle of the warming drawer.

Removal

When installing two appliances side-by-side, the door handles

/ recessed grips must be in the centre.

If there is no fitted shelf above the appliance, secure the

appliance against tipping over when the door is opened. Fit

two standard angles 5 mm above the appliance at 450 mm

depth inside the cabinet.

Fully insert the appliance in the cabinet.

Do not kink or trap the power cable, or route it over sharp

edges.

Centre the appliance.

There must be an air gap of 5 mm between the appliance and

adjacent cabinets.

Using a spirit level, adjust the appliance so that it is perfectly

level.

Screw the appliance firmly in place with the screws provided.

Disconnect the appliance from the power supply.

Undo the securing screws.

Lift the appliance slightly and pull it out completely.