ADELSYSTEM CBI6012A Manuale di istruzioni - Pagina 2

Sfoglia online o scarica il pdf Manuale di istruzioni per UPS ADELSYSTEM CBI6012A. ADELSYSTEM CBI6012A 5. Dc ups

Stampa la pagina

Battery Config - Life test – Fast Charge – UPS Disabling-

Time Buffering

Aux4: Ethernet

Network Communication LED

ADELBus (CAN)

Rectifier Alarm

PE for Aux4 "Shield"

Connection terminal and wiring

The following cable cross-sections may be used:

Solid

Stranded

(mm2)

In:

0.2–2.5

Out:

0.2–2.5

Signal:

Screw type terminals, 2.5 mm2. Wiring shall be marked to indicate the

proper connection for the power supply. Use copper cables only; for

power connections use wires suitable for at least 75°C

Input and Output Battery connection

Input AC Port L – N:

No.10: Single phase Switching Power Supplies L, N, PE

Battery Connection and Load Connection

Battery Connection Port:

No.1:

-Connect the battery between: terminal 3 (–) and 4 (+)

-One battery (12 Vdc) for CBI12xx;

-Two battery (12 Vdc) connected in Series for CBI24xx;

Output Load:

No.2: Connect this output to the load, terminal 1 (–) and 2 (+).

Drive and Monitoring

Fault - Status conditions

STATUS: Mains or Backup: Input Mains On/Off.

•

No.5 Output Open Collector Contact: 1

•

No.6: LED

Fault Battery or Fault System

•

No.4 Output Open Collector Contact: 2

•

No.7: LED

•

No.8: Led DIAGNOSIS: Diagnosis of the system through

"blinking code" light signal

Fault Internal Rectifier

•

No.23 Output Open Collector Contact: 3

Driver Contact open drain:

Mains/Back-Up

Port N°5

Closed

Mains Input Vac

OFF

Open

YES

Open

Battery SOC

less than 30%

Open

YES

Battery or

system Fault?

Stripping Length

Torque

AWG

(Nm)

24 – 14

0.5–0.6

7 mm

24–14

0.5–0.6

7 mm

AMP Modu II

Open drain referred to the Load

negative terminal; requires an external

DC power source (max 48Vdc) – drain

current: 20 mA Nom ; 40 mA Max for 3

sec

Battery or System fault

Led N°6

Port N°4

Led N°7

■ - led off

Closed

■ - led On

■ - led off

Closed

■ - led On

Open

■ - led On

■ - led off

Closed

■ - led off

■ - led On

Open

■ - led off

Closed

Via Luigi Barchi 9/B – Reggio Emilia 42124 – Italy

Tel. +39 0522 345518 – Fax +39 0522 345551 –

Charging Mode Status

Status

Float

Absorption

Charging Type

Bulk

Recovery

Faulty Battery / Faulty System

Reverse polarity or high battery Voltage

(over 32.5Vdc for CBI 24xxA)

Battery not connected

Battery element in Short Circuit

Overload or short circuit on the load

Bad battery; Internal impedance Bad or Bad battery wire connection

Life test not possible

Rectifier Alarm

Boost condition; battery discharge after 4 min. of overload.

Low battery (under 18.5Vdc for CBI 6024A) Only if started from

battery, no mains input

Mains detector failure

Device over-temperature Alarm

Calibration error

Start from Battery No Input Mains Vac

No. 9: Push-button, max 3 sec., in the front panel to switch ON

the system without the "Mains input Vac" but only the battery

connected. Same function for additional external Button by

connection of pin N°12 (SB). The other side of the external

button must be connected to Negative Load.

Load ON/Off

It is possible to Drive the output Load On/Off by Ethernet connection. This

function allows to switch On/Off the load output for many application as,

Reset PLC, staircase light timer control, emergency light controls, etc...

Charging Current limiter:

In order to protect the battery from excessive

charging currents, the device allows to limit the

maximum charge current by Push Button. Press

button (9) for 2 sec., after that in 20 step it is

possible to select the limit current. Press for

more than 2 sec. to store the selection in

permanent memory.

CBI6024A: from 0 – 3A ; 20 step; 1 step 150mA

CBI6012A: from 0 – 5A ; 20 step; 1 step 250mA

It is possible set the limiting current also by the internal Web Server,

please refer to the Ethernet section.

Battery Care

The Battery Care philosophy is based on algorithms that implement rapid

and automatic charging, battery charge optimization during time, flat

batteries recovery and real time diagnostic during installation and

operation. Elements in short circuit, accidental reverse polarity

connection, disconnection of the battery, can easily be detected and

removed by help of Blink Code of Diagnosis Led, during the installation

and after sale. Each device is suited for all battery types, it is possible to

set predefined curves for Open Lead Acid, Sealed Lead Acid, Gel, Ni-Cd,

Li-Ion. They guarantee battery reliability over time by continuously testing

the internal impedance status, avoiding any possible risk of damage and

granting a permanent, reliable and safe connection of the battery to the

power supply. The system includes a battery stimulation circuit and

sophisticated algorithms to recognize sulphated batteries or batteries

with a short-circuited element. Battery Test: Automatic. battery

connection check: every 60 seconds. Battery efficiency test: every 220

minutes in float charge. Battery Faults can be monitored by relay and led

blinking.

Battery Charge in Temperature compensated

environment

No. 11 Auxiliary Output "AUX 1"

It is possible to connect the Temperature sensor probe and apply it on

the battery.The function of the probe is for temperature battery

compensation. With this it is possible to meet the requirements of the

EN54- fire certification.

www.adelsystem.com

Instruction Manual CBI60_4

Diagnosis (No.8)

Battery fault (No.7)

1 Blink/2 sec

OFF

1 Blink/sec

OFF

2 Blink/sec

OFF

5 Blink/sec

OFF

1 Blink/pause

2 Blink/pause

3 Blink/pause

4 Blink/pause

5 Blink/pause

6 Blink/pause

7 Blink/pause

8 Blink/pause

10 Blink/pause

12 Blink/pause

14 Blink/pause

16 Blink/pause

Page 2